Chevrolet Silverado Rear Vision System Nav Display Installation Instructions

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.

2003-07 Dodge Dakota 4.7L PowerAid Throttle Body Spacer

Your PowerAid Throttle Body Spacer was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, please contact AIRAID.
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake hose assembly.
3. Remove throttle body air intake box and save bolts.
4. Remove (3) bolts from the throttle body.

Dodge Nitro Eibach Pro-Kit Spring Installation

I am not a mechanic, nor do I claim to know the best way to install this kit. This is simply a document detailing
the method I used to install the springs on my wife’s 2007 Dodge Nitro R/T 4.0L.
Installation:
1. Read through all the instructions at least 1 time, and then begin the installation process.
2. Using the 10mm wrench, remove the battery terminal connectors.
3. Remove the bottom bolt from the battery tray; this should free the battery to be lifted out.
4. After the battery has been removed, open the fuse box and disconnect the RED cable using a 13mm socket.

2002-2006 Honda CR-V Subwoofer Kit Installation Instructions

The subwoofer can not be installed with an under-seat CD changer.
Installation the Subwoofer to 2002-2006 CRV:
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Remove the two screws that fasten the bottom of the center panel.
4. Pull the center panel out toward you to release the six clips, unplug the vehicle connector from the hazard switch, and remove the center panel. Be careful care not to damage the clips.

2003 Nissan 350z Driver's Seat Click Noise or Side to Side Movement When Turning

When tuning left or right,
• The driver’s seat makes a “click” noise, and/or
• The driver’s seat moves side to side (left or right),
ACTION:
• Install special washers between the seat thigh support adjuster and the sliding and reclining device—inner and outer (see Figure 1).
NOTE: This is the only authorized repair for this incident (i.e. click noise or side to side movement when turning).
SERVICE PROCEDURE
NOTE: Steps a, b and c below only apply to vehicles equipped with front side (SRS) air bags.
a. Write down all radio station presets.
b. Disconnect the negative battery cable.
c. Wait at least 3 minutes after the negative battery cable is disconnected before removing the driver’s seat.

Land Rover Fusible CV Conversion Fitting Instructions

KAM LAND ROVER FUSIBLE CV CONVERSION
CV Joint Removal
1. Drive vehicle for 5 miles to preheat axle lubricant.
2. Using a suitable container remove drain plug on axle and swivel housing and allow lubricant to drain. Re-fit drain plugs.
3. Jack and secure vehicle and remove road wheel.
4. Remove brake calliper and secure to chassis ensuring excessive strain is not applied to brake lines.
5. Remove hub-driving member dust cap and external cir-clip and shims from CV shaft.
6. Loosen bolts and remove hub-driving member.
7. Drift locking tab clear of wheel bearing nuts and remove wheel-bearing nuts.
8. With care to avoid damage to hub seal, withdraw hub from stub-axle.
9. Loosen and remove stub axle bolts and mud shield.
10. Remove stub axle from swivel housing. A light knock from a soft-faced mallet may be required to break seal.
11. Withdraw CV joint and axle half-shaft.

1991-96 Ford Escort Baseplate BX2112 Installation Instructions

Installation of this baseplate requires removing the plastic belly pan. The brackets attached to the vehicle's frame and the tie down brackets also need to be removed. They will be replaced with the baseplate's side mounts. The plastic around the tie down brackets will need to be trimmed.
1. Read the General Instruction Sheet included with this baseplate.
2. Under the front corners of the car there is a stamped metal bracket that protrudes down with a slot at the bottom. These are called the tie down brackets. The baseplate mounts to the outside of the tie down brackets and to the center engine support bolts, using ten bolts, eight of which are supplied with the baseplate.

00-05 Mitsubishi Eclipse Front Kit Part No. 75504

Always keep safety in mind when working on your vehicle. Completely read these instructions before installing the kit.
Preparing the Vehicle
1. Elevate the vehicle and secure the frame with jack stands.
2. Remove the front wheels.
Strut Removal
1. Remove the three nuts securing the upper strut mounting bracket and discard.
NOTE: These are located inside the engine compartment above the strut pocket.

Mitsubishi Lancer Short Throw Shifter Installation Manual

Follow the steps below for installation the short throw shifter on your Mitsubishi Lancer
1. Carefully unscrew the stock shift knob.
2. Remove ashtray and screw beneath it.
3. Remove two screws from inside the center console storage compartment.
4. Lift up on the rear section of the center console and unclip it from the front section.
5. Remove plastic screw from the driver’s side of the center console (near the gas pedal). Remove the plastic cover and the pop rivet beneath it. Then remove the two screws at the rear of the console (were hidden by the rearward part of the center console that was removed).

Remote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start

Preparation the Toyota Camry for installation
-Remove the driver’s side under dash, as well as the knee airbag bolts. Move the Airbag aside, but DO NOT DISCONNECT the Airbag connector in order to avoid setting any vehicle codes.
-Remove the driver’s side floor heating duct, in order to access the vehicle IMI & IMO wires easily.
The remote car starter will be installed in a conventional manner even if the car is equipped with the Smart Key “Push-to-Start” system.

1999-2000 Toyota Camry Radio Replacement

The plastic dash panel surrounding the radio and air conditioner controls must be unsnapped from the dash in order to gain access to the bolts which secure the radio. Pull out the ashtray at the bottom of the plastic dash panel. With your hands, grab the bottom of the plastic dash panel below the ashtray location and pull firmly until the plastic dash panel begins to unsnap from the dash. Continue to pull the dash until the sides and top of the dash panel completely unsnap from the main dash assembly. The radio is secured to the dash with four (4) 10 mm bolt screws, (1) at each side corner of the radio. Locate and remove all four bolt screws. Pull the radio out of the dash. Unplug the black cable plugged into the rear of the radio. Unplug (2) white plastic wire harness connectors snapped into the rear of the radio. The radio can now be completely removed from the dash.

98-01 Toyota Corolla Sport Sway Bar Set Installation

INSTALLATION OF HOTCHKIS FRONT SWAY BAR
1.) Please look at the original front antiroll bar and note the orientation of the front bar. You will want to install the new Hotchkis bar in the same manner.
2.) Use a 14mm wrench and 6mm Allen wrench to remove the nuts holding the end links to the ends of the stock sway bar. Remove the end links from the ends of the sway bar. Retain the hard ware for later use.
3.) Remove the cross piece from the sway bar mount on each side using a 19mm wrench or socket.
4.) Using a 12mm socket or wrench remove one the three mounting brackets.

2004-05 Chevy Colorado Prerunner Rear Bumper Installation

This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.

2006-2008 Honda Pilot Dash Disassembly

1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Using a small flat blade screw- driver remove the blank plate from upper right side of radio trim panel. (Figure A) 3 Unsnap radio trim panel. Unplug switches and remove panel. (Figure B) 4 Remove (4) 10mm bolts securing radio, unplug and remove radio.

2004-2006 Chevy Colorado Brute Force Intake System Installation

Getting Started
a) Make sure vehicle is parked on a level surface. Set parking brake.
b) Disconnect negative battery terminal from the battery.
c) If engine has run within the past two hours, let it cool down.
Removal of the stock intake system.
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process.

2005-Present Pontiac G6 Figure Grille Set Installation Instructions

These grilles are fabricated employing quality materials and finishes, and have been engineered to enhance the look of your vehicle for the duration of its life. Proper installation is essential to your overall satisfaction, so please read these instructions before attempting to install the grilles. Exercise patience; these instructions are intended to assist even the most mechanically challenged.

Vauxhall Cavalier/Opel 4 x 4 Transfer Box Installation

This procedure assumes the removal procedure has been read and/or followed. CAUTION: If you followed the removal procedure, the gearbox may NOT have any oil in it - do not forget. 500. Inspect the txb (Transfer box) before reinstalling, Clean off any excess jointing compound.
501. Lightly apply grease to the flange of the txb to gearbox coupling (two visible splined shafts), and apply the rubber 'O' ring to the flange.
502. Apply masking tape (Fig.1B) or similar to the fluid coupling and the txb breather/filler connections to prevent ingress of unwanted material while installing the txb.

2005 Cadillac CTS V Power Steering Pump Replacement

Identifying Power Steering Reservoir Outlet Hose At Power Steering Pump
1. Remove the front air deflector. Refer to Air Deflector Replacement - Front in Body Front End.
2. Place a drain pan under the vehicle.
3. Remove the power steering pulley. Refer to Power Steering Pulley Replacement.
4. Remove the power steering reservoir outlet hose from the power steering pump.
5. Disconnect the power steering pressure line from the power steering pump.
6. Remove the power steering cooler outlet hose from the power steering reservoir
7. Remove the power steering pump to power steering pump bracket bolts.
8. Remove the power steering pump from the power steering pump bracket.

2005-Up Pontiac G6 Figure Grille Set Installation Manual

These grilles are fabricated employing quality materials and finishes, and have been engineered to enhance the look of your vehicle for the duration of its life. Proper installation is essential to your overall satisfaction, so please read these instructions before attempting to install the grilles. Exercise patience; these instructions are intended to assist even the most mechanically challenged.

2002 Chevy/GMC 3500-series Dual Underpro Speaker Installation Guide

This document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation and/or operation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that could prevent serious injury or damage.