This bar was designed to replace your original equipment sway-bar. The diameter of the bar has been increased for more roll resistance; the contours of the bar may differ slightly, if some of the bends were not necessary. This kit may come with none, some or all of the hardware required to install the bar depending on the application. If hardware is not included with the kit, the hardware from the O.E. bar must be retained and re-used. If these parts are too worn to be re-used it will be necessary to obtain them from your O.E. parts dealer. If your car/truck was not equipped with O.E. bar, the installation of this bar may not be possible.
Showing posts with label original equipment. Show all posts
Showing posts with label original equipment. Show all posts
Wednesday, September 22, 2010
Chevrolet Van 97 & Up Sway Bar Installation
1:17 AM by onesecond
·
0
comments
Labels: bends, binding effect, bushings, car truck, Chevrolet, chevrolet van, contours, diameter, interference, original equipment, rear sway bar, resistance, road test, step 1, step 3, suspension travel, sway bars, tire clearance, wheels
Labels: bends, binding effect, bushings, car truck, Chevrolet, chevrolet van, contours, diameter, interference, original equipment, rear sway bar, resistance, road test, step 1, step 3, suspension travel, sway bars, tire clearance, wheels
Saturday, June 26, 2010
2004-05 Chevy Colorado Prerunner Rear Bumper Installation
11:38 PM by onesecond
·
0
comments
Labels: bolts, brackets, Chevrolet, chevy colorado, harness connector, license plate light, mechanical condition, original equipment, PDF Download, plastic tabs, rear bumper, stock, tow wire, trailer tow, wire harness
Labels: bolts, brackets, Chevrolet, chevy colorado, harness connector, license plate light, mechanical condition, original equipment, PDF Download, plastic tabs, rear bumper, stock, tow wire, trailer tow, wire harness
This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.
Wednesday, May 26, 2010
1994-1997 Cadillac Seville Revised HVAC Blower Motor Installation Procedures
3:43 AM by onesecond
·
0
comments
Labels: cable failure, Cadillac, cadillac seville, canister purge solenoid, car harness, caution, customer satisfaction, electrical component, electrical loads, heating ventilation and air conditioning, hvac blower motor, negative battery cable, original equipment, personal injury, purge valve, screws, solenoid, solenoid valve, valve replacement, ventilation
Labels: cable failure, Cadillac, cadillac seville, canister purge solenoid, car harness, caution, customer satisfaction, electrical component, electrical loads, heating ventilation and air conditioning, hvac blower motor, negative battery cable, original equipment, personal injury, purge valve, screws, solenoid, solenoid valve, valve replacement, ventilation
The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.
The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.
In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.
The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.
In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.
Monday, May 24, 2010
Chrysler, Dodge and Plymouth Transmission Mount Installation Instructions
5:00 AM by onesecond
·
0
comments
Labels: Chrysler, chrysler dodge, Dodge, energy suspension bushings, job, leading edge, new energy, original equipment, outer shell, plymouth, protective safety gear, straight tube, ventilated area
Labels: Chrysler, chrysler dodge, Dodge, energy suspension bushings, job, leading edge, new energy, original equipment, outer shell, plymouth, protective safety gear, straight tube, ventilated area
Installation instructions:
1. Remove the bracket assembly from the vehicle.
2. Remove all of the old rubber from inside of the original shell before installing the New Energy Suspension bushings. If heat is used to remove the old rubber, you need to only heat the outer shell enough to loosen the bond of the old rubber. Do NOT burn out the bushing. Always use the proper protective/safety gear for the job and work in a well ventilated area.
1. Remove the bracket assembly from the vehicle.
2. Remove all of the old rubber from inside of the original shell before installing the New Energy Suspension bushings. If heat is used to remove the old rubber, you need to only heat the outer shell enough to loosen the bond of the old rubber. Do NOT burn out the bushing. Always use the proper protective/safety gear for the job and work in a well ventilated area.
Subscribe to:
Posts (Atom)
