Nissan 300ZX HKS Twin Power Ignition Amplifier Installation Guide

Most will say that the stock ignition system of the 300zx is sufficient unless you are running extreme levels of boost.
However there are others that say that they get increased throttle response and a slight performance gain from this modification.

1996-1999 Nissan Pathfinder (R50) Automatic to Manual Transmission Conversion Manual

This manual will, in detail, give the information you will need to convert a 4x4 1996-1999 Nissan Pathfinder from an automatic transmission to a manual transmission. Having a manual transmission in your Pathfinder gives you more control, lower gears, and more power than you would have with an automatic. Other benefits include better gas mileage, lower maintenance cost and reduced electronic dependence.

Nissan Skyline R34 GTS VX Plug-In Installation and Configuration Manual

Vi-PEC Engine Management Systems are designed with the final result in mind. Not only do they boast an impressive range of performance features, but are designed with a focus on safety, reliability and drive-ability. However, the ultimate success of your engine management upgrade is determined by how well the system is installed and tuned.

Nissan Titan King Cab Vehicle Specific Subwoofer Enclosure

The enclosure mounts under rear seat firing down, in Nissan Titan King/Crew Cab trucks.
TOOLS REQUIRED FOR INSTALLATION: Powered Screwdriver 6" Bit Holder Extension Socket Wrench
INSTALLATION: Follow the steps below
1. Slide front seats to full forward position. This will give you more room to work with.

Engine Torque Link Installation Procedure

1) Remove front engine mount upper bolt with 14mm socket. The front engine mount is located on the timing cover side of the engine also known as the front of the engine.
2) Install the small torque link bracket as shown in picture. Use supplied M10 bolt and tighten to finger tight. A 13mm wrench or socket is used for this bolt. Do not torque down this bolt just yet.

JWT Nissan Single Fogger Nitrous Oxide System Installation Instructions

This SYSTEM CONSISTS OF A CONVENTIONAL solenoid operated nitrous oxide spray nozzle. However the supplemental fuel is not added by a separate fuel spray nozzle, as with most conventional N2O systems. Older conventional systems sprayed supplemental fuel through the intake manifold along with the nitrous oxide, requiring the addition of a extra solenoid, line and fuel source. Most fuel injected engines have intake runners that are designed to run "dry" and will not

1993-2002 Nissan Pathfinder Road Companion

The Pathfinder was first launched in 1987 as a derivative of Nissan’s pickup truck line. Available initially as a two-door, it was joined by a four-door version in 1990, which has been the sole body style since 1991. The original Pathfinder changed very little on the outside during its life, but was treated to a new dash and interior design in 1994. Whereas the first-generation Pathfinder was a body-on-frame design, the all-new 1996 Pathfinder featured unibody construction. In

Nissan Patrol Diesel System Case Study

A BDS Unit is a solid state device that produces a specific engineered frequency that can change the structure of diesel fuel to produce more complete combustion of the fuel. This nanotechnology is a completely new approach to fuel management. The transfer of the engineered frequency from the BDS to the fuel line begins to produce fuel and emissions

2002-04 Nissan Altima Dyno-Proven Cold Air Intake System Installation

All 2004 vehicles that are considered LEV2 and SULEV with engine test group numbers of families do not satisfy or meet the California air resource board tet procedures. The engine group test numbers can be found on the underhood information label located on the drivers side. Engine test group numbers listed below are to be considered for off-road use only: 2004 Nissan Alima 2.5L test group number- 4NSXV02.585A

Nissan 200sx SR20DET Engine Tuning Guide

This document explains the engine various modifications, with a common path through them. However, these various modifications can be done in many different orders, and this is merely a guide.

03-06 Nissan 350Z Oil Cooler Installation Instructions

1. Install the small rubber o-rings supplied with the kit onto all the fittings that screw into the oil outlet and inlet ports (threaded). Every connection to the oil filter sandwich block will require a rubber o-ring gasket. Do not use any thread sealer or Teflon tape on any of the fittings to the oil filter, block, cooler, or cooler lines. If you are installing an oil

95-98 Nissan 240SX EMS P/N 30-1611 and 30-1611U Installation

The AEM Engine Management System (EMS) is the result of extensive development on a wide variety of vehicles. Each system is engineered for a particular application. The AEM EMS differs from all others in several ways. The EMS is a “stand alone”, which completely replaces the factory ECU and features unique plug and play technology. There is no need to

2003-2007 Nissan Murano Engine Air Intake Duct Service Bulletin

Nissan is conducting a voluntary safety recall on model year 2003 – 2007 Murano vehicles. Under certain conditions, the intake duct, which is connected to the intermediate resonator in the air intake system of the engine, may separate from the resonator with engine movement. This could cause minor idle fluctuation or poor acceleration. If this occurs, and the vehicle continues to be driven without being serviced, the engine may stall while driving. To remedy this potential condition, Nissan is conducting this voluntary safety recall campaign to replace the air intake duct with an updated part and the air duct clamps with new clamps at no charge for parts or labor.

Nissan Evaporative (EVAP) Emission Control System Cleaning Procedure Service Bulletin

If the EVAP canister leaks (or has leaked) charcoal, it must be replaced. In addition to replacing the canister, the entire EVAP emission control system must be cleaned to remove charcoal particles released by the leaking canister. To clean the EVAP emission control system, use the service procedure starting on page 3.

Nissan Vent Control Valve Replacement Service Bulletin

All Nissan models using Vent Control Valve P/Ns 14935-AM60A / AM60B
SERVICE INFORMATION
When replacing the EVAP canister vent control valve for any reason: Use the one listed in the PARTS INFORMATION section of this bulletin on Page 2. For vent control valve replacement procedure, refer to the appropriate section of the Electronic Service Manual (ESM) if needed.

2003-Up Nissan 350Z Edelbrock Nitrous System

The Edelbrock Nissan 350Z Performer EFI Nitrous System (Part Number 71007) is designed for 2003-Later Nissan 350Z vehicles equipped with stock 3.5L engines that utilize the returnless style fuel system. Horsepower and torque increases can vary with equipment upgrades and modifications.

Hybrid Nissan N14 GTi-R intercooler kit Installation instruction

Please remove the Std intercooler ,top Std intercooler pipe , front bar ,front reinforcement prior install the top Hybrid intercooler pipe. (make sure all super clamps are loose for further adjustments.)
Enlarge the hole behind the driver side head light to clear the top pipe
Enlarge the hole behind the passenger side head light to clear the top pipe

Nissan Satellite Radio Diagnostic Information

Applied Vehicles: All 2004 Nissan Vehicles and later - equipped with XM® or SIRIUS™ Satellite Radio Receiver and Service.
IF YOU CONFIRM: A satellite (SAT) radio related incident has occurred on a Nissan vehicle factory equipped with SAT radio.
ACTIONS: First, refer to Chart A (page 2) for a list of Nissan vehicles that are pre-wired for SAT radio.
Second, refer to the Service Information section (page 3) in this bulletin. The Audio unit, SAT receiver, and Satellite Service may be OK.
Third, refer to the Service Procedure section (page 6) of this bulletin.
The Service Procedure section contains a Diagnostic Flowchart. It will provide Symptoms and Possible Causes to help you judge the SAT radio condition.

2003 Nissan 350z Driver's Seat Click Noise or Side to Side Movement When Turning

When tuning left or right,
• The driver’s seat makes a “click” noise, and/or
• The driver’s seat moves side to side (left or right),
ACTION:
• Install special washers between the seat thigh support adjuster and the sliding and reclining device—inner and outer (see Figure 1).
NOTE: This is the only authorized repair for this incident (i.e. click noise or side to side movement when turning).
SERVICE PROCEDURE
NOTE: Steps a, b and c below only apply to vehicles equipped with front side (SRS) air bags.
a. Write down all radio station presets.
b. Disconnect the negative battery cable.
c. Wait at least 3 minutes after the negative battery cable is disconnected before removing the driver’s seat.

2003 350Z MIL ‘ON’ DTC P0442 (Evap Small Leak) Stored In Self Diagnosis Results

An Applied Vehicle has a MIL “On” and has one or both of the following DTCs stored in the ECM:
• P0442 EVAP Small Leak
• P0456 EVAP Very Small Leak
ACTIONS:
Confirm this bulletin applies. Perform CONSULT-II Self-Diagnosis (repair as needed). ECM Part Number Check to determine if this bulletin applies. ECM Reprogramming (needed if a match is found during ECM Part Number Check).
IMPORTANT: The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure (starting on page 2) as it contains information that is essential to successfully completing this repair.