2003-2007 Nissan Murano Engine Air Intake Duct Service Bulletin

Nissan is conducting a voluntary safety recall on model year 2003 – 2007 Murano vehicles. Under certain conditions, the intake duct, which is connected to the intermediate resonator in the air intake system of the engine, may separate from the resonator with engine movement. This could cause minor idle fluctuation or poor acceleration. If this occurs, and the vehicle continues to be driven without being serviced, the engine may stall while driving. To remedy this potential condition, Nissan is conducting this voluntary safety recall campaign to replace the air intake duct with an updated part and the air duct clamps with new clamps at no charge for parts or labor.

94-2002 Dodge Turbo Air Guide (TAG & TAG-II) Install

The TAG is intended to be used with the silencer ring in place. On 94-2002 Dodge trucks install the longer side into the turbo housing and the shorter side will be facing the inside of the intake boot. Remove the rubber boot from the turbo charger inlet and insert the TAG into the rubber boot with the longest part of the TAG facing outward as shown. The TAG should snap into the groove inside the boot. Place the supplied band clamp over the hose as shown in the photo below. Slip the boot back over the turbo inlet using one hand through the boot to guide the TAG into the turbo.

2004+ Subaru Impreza WRX/STI Front Lip (polyurethane)

Polyurethane is a flexible material. Occasionally during shipping, sections of the lip may warp or bend in unusual shapes. DO NOT WORRY! Simply lay the lip flat and out in the sun for a day and it will return to its normal shape. To cure the waviness of the front portion, simply purchase a long metal or wood section, clamp this metal section inside the lip (clamps can be purchased at Home Depot), and lay out in the sun for about a day. This will fix the waviness problem.

Honda CR-V DVD Navigation Attachment

DVD AVN Navigation Unit P/N: 08A40-1J6-100
Wire Harness Routing Precaution
Disconnect the connectors and terminals by holding them. Do not pull the harness to disconnect the connector.
Do not pull the harness with force. it will damage the har ness.
Cut off the excess of the wire ties.
Connect the connectors and terminals securely until they lock.
Reinstall the connectors to the corresponding stays whenever they are removed. After operation, check that the connectors are installed on the stays securely and not loose or come out of the stays.

Power Steering, Air Cleaner Element

Always use Genuine Honda Power Steering Fluid. If it is not available, you may use another power steering fluid as an emergency replacement. However, continued use can cause increased wear and poor steering in cold weather. Have the power steering system flushed and refilled with Honda PSF as soon as possible. A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible.

2007 Toyota Camry Hybrid Sirius XM Radio Satellite Installation

Cable Routing and Installation (a) Install and route the tuner cable from the center cluster and along the front support bar. (Fig. 3-1) (b) Provide sufficient cable slack to connect to the tuner, and then secure the cable to the existing wire harness with lock tie. Cut excess off lock tie. Connect wire harness to head unit. (c) Using lock ties attach to existing W /H. Trim lock tie excess. (Fig. 3-2) (d) Route to the existing clamps. (Fig. 3-2) (f) Route the cable as shown and secure with lock tie. Trim lock tie excess. (Fig. 3-4) (g) Route the tuner cable under the rear passenger seat and secure with cushion tape. (Fig. 3-5) NOTE:Clean the area for the cushion tape with the approved cleaner.

Chrysler 300C 5.7L Hemi Engine Dynomax Kit 19412 Installation

This dynomax kit for chrysler 300C 5.7L Hemi Engine installation steps:
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂" clamps that connect the mufflers to the x-pipe.

07-Up Chevy Tahoe LED Upper Quarter Panel Light

Your new IPCW LED Upper Quarter Panel Lights are quality-made products that will work beautifully on your vehicle. Please refer to the pictures below for installation instructions.
Remove the screws in Figure A with a Phillips screwdriver. Untwist the sockets, then gently slide out the tail light.
After the tail light is removed. remove the screw in Figure B.
Remove the screw in Figure C to remove the Upper Quarter panel.
Gently slide out the stock Upper Quarter Panel.

2007-2008 BMW E82/88 135i Intake kit Installation Instructions

Step 1: Complete Stock Intake.
Step 2: Disconnect vacuum line and pull back.
Step 3: Unclip upper half of air box to remove lid and filter.
Step 4: Pull back rubber mount attached to battery cable. Use pliers if necessary. This will allow stock clamp to be loosened. (To be done in step 5B.)
Step 5: A) Loosen clamp closest to the radiator with 1/4” nut driver. B) Loosen clamp closest to fire wall with 1/4” nut driver. Leave clamps in position.