DVD AVN Navigation Unit P/N: 08A40-1J6-100
Wire Harness Routing Precaution
Disconnect the connectors and terminals by holding them. Do not pull the harness to disconnect the connector.
Do not pull the harness with force. it will damage the har ness.
Cut off the excess of the wire ties.
Connect the connectors and terminals securely until they lock.
Reinstall the connectors to the corresponding stays whenever they are removed. After operation, check that the connectors are installed on the stays securely and not loose or come out of the stays.
Showing posts with label pins. Show all posts
Showing posts with label pins. Show all posts
Sunday, November 14, 2010
Honda CR-V DVD Navigation Attachment
1:52 AM by onesecond
·
0
comments
Labels: airbag, clamps, curtain, har, Honda, honda cr v, model 1, navigation unit, pillar, pins, precaution, sunvisor, tabs, torx screws, wire harness, wire ties
Labels: airbag, clamps, curtain, har, Honda, honda cr v, model 1, navigation unit, pillar, pins, precaution, sunvisor, tabs, torx screws, wire harness, wire ties
Tuesday, November 9, 2010
2002-2006 Honda CR-V Subwoofer Kit Installation Instructions
3:30 AM by onesecond
·
0
comments
Labels: antenna, bolts, careful care, dashboard, flat tip, fuse box, glove box, hazard switch, Honda, honda cr v, negative cable, pins, radio station, retaining clips, seat cd changer, self tapping screw, self tapping screws, subwoofer, tabs
Labels: antenna, bolts, careful care, dashboard, flat tip, fuse box, glove box, hazard switch, Honda, honda cr v, negative cable, pins, radio station, retaining clips, seat cd changer, self tapping screw, self tapping screws, subwoofer, tabs
The subwoofer can not be installed with an under-seat CD changer.
Installation the Subwoofer to 2002-2006 CRV:
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Remove the two screws that fasten the bottom of the center panel.
4. Pull the center panel out toward you to release the six clips, unplug the vehicle connector from the hazard switch, and remove the center panel. Be careful care not to damage the clips.
Installation the Subwoofer to 2002-2006 CRV:
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Remove the two screws that fasten the bottom of the center panel.
4. Pull the center panel out toward you to release the six clips, unplug the vehicle connector from the hazard switch, and remove the center panel. Be careful care not to damage the clips.
Thursday, October 21, 2010
G35 Coupe Aluminum Pedal Install
1:26 AM by onesecond
·
0
comments
Labels: 6mt, aluminum, brake pedals, clutch, gas pedals, grubbs infiniti, Infiniti, Nissan, nissan 350z, pins, plastic bags, salesmen
Labels: 6mt, aluminum, brake pedals, clutch, gas pedals, grubbs infiniti, Infiniti, Nissan, nissan 350z, pins, plastic bags, salesmen
I purchased the Infiniti aluminum pedal set from Grubbs Infiniti in Dallas over the phone from Danny our FX45 salesmen. I believe Danny said these pedals are the ones used in the FX45. After examining them, I think he's probably right because the dead pedal is narrower and sits up higher than either the standard G35 plastic dead pedal or the Nissan 350Z dead pedal. The brake and gas pedals look the same.
Parts
All of the parts in their respective plastic bags with part numbers. These are for the 5AT. For the 6MT the clutch and brake pedals are different. Total price ~$80 shipped.
Parts
All of the parts in their respective plastic bags with part numbers. These are for the 5AT. For the 6MT the clutch and brake pedals are different. Total price ~$80 shipped.
Wednesday, August 25, 2010
Acura/Honda Car2PC-HON1 adapter for Car PC / laptop integration into car stereo
3:28 AM by onesecond
·
0
comments
Labels: Acura, audio cables, car engine, car pc, car stereo, cd changer, cd drive, disk 1, glove box, Honda, many cars, pc laptop, pins, playlist, playlists, radio adapter, usb cable, winamp plug, windows 2000, windows media player
Labels: Acura, audio cables, car engine, car pc, car stereo, cd changer, cd drive, disk 1, glove box, Honda, many cars, pc laptop, pins, playlist, playlists, radio adapter, usb cable, winamp plug, windows 2000, windows media player
Preparation
1. Turn off car engine and remove key from ignition
2. Un-mount your radio from the dash in order to get access to the back side of the radio.
Adapter installation
3. Attach square 14 pins connector to the back of the Honda stereo.
4. Find a place where you can place Car2PC. In many cars there is enough room in the dash to place Car2PC.
Note: Make sure you mount Car2PC in a place with enough room so when you mount the car stereo back you do not break the adapter
1. Turn off car engine and remove key from ignition
2. Un-mount your radio from the dash in order to get access to the back side of the radio.
Adapter installation
3. Attach square 14 pins connector to the back of the Honda stereo.
4. Find a place where you can place Car2PC. In many cars there is enough room in the dash to place Car2PC.
Note: Make sure you mount Car2PC in a place with enough room so when you mount the car stereo back you do not break the adapter
Wednesday, May 19, 2010
2008 Ford Super Duty F-250/350/450/550 Mount Kit Installation Instructions
4:22 AM by onesecond
·
0
comments
Labels: blade, electrical connectors, f 250, Ford, ford super duty, left hand, pins, push pin
Labels: blade, electrical connectors, f 250, Ford, ford super duty, left hand, pins, push pin
Contents of this ford super duty mount kit instruction
Attach:
1. Push Pin Release Handle down to pull out Connecting Pins.
2. Drive vehicle slowly to engage Pushplates into Attachment Arms.
3. Stand in front of blade. Fully raise Pin Release Handle to release Connecting Pins.
4. Push Headgear toward vehicle to allow Connecting Pins to fully engage Pushplates. If unable to push Headgear from in front of blade, stand in front of Headgear on driver side and push Headlamp Bracket.
5. Pull out Jack Lock. Push Pin Release Handle into Stop.
Attach:
1. Push Pin Release Handle down to pull out Connecting Pins.
2. Drive vehicle slowly to engage Pushplates into Attachment Arms.
3. Stand in front of blade. Fully raise Pin Release Handle to release Connecting Pins.
4. Push Headgear toward vehicle to allow Connecting Pins to fully engage Pushplates. If unable to push Headgear from in front of blade, stand in front of Headgear on driver side and push Headlamp Bracket.
5. Pull out Jack Lock. Push Pin Release Handle into Stop.
Tuesday, May 18, 2010
Disabling Daytime Running Lights (DRL) for VW Passat
11:10 PM by onesecond
·
0
comments
Labels: 8t, b5, caution, closer look, damages, daytime running lights, drl, euroswitch, fuse panel, headlights, light switch, notch, passat, pin connectors, pins, trims, Volkswagen, volkswagen passat, vw passat, warranty
Labels: 8t, b5, caution, closer look, damages, daytime running lights, drl, euroswitch, fuse panel, headlights, light switch, notch, passat, pin connectors, pins, trims, Volkswagen, volkswagen passat, vw passat, warranty
A wiring diagram of the headlights for the 2001.5 VW Passat (may or may not apply to other model years). First method: Pulling out DRL relay 173 The fuse panel with cover. The driver side door has to be open. Remove the fuse panel cover. Start by prying through the notch shown above. These were done on a 2001.5 Volkswagen Passat 1.8T. It may also apply to other model years and trims. Look inside behind the fuse panel. You'll see the relay panel and relay 173. A closer look at relay 173 installed. Pull relay 173 out to disable the daytime running lights.
Second method: Modifying the light switch The pin connectors at the back of the light switch.
Second method: Modifying the light switch The pin connectors at the back of the light switch.
Friday, May 14, 2010
GRIP Chevy Cobalt Body Kit Installation
2:37 AM by onesecond
·
0
comments
Labels: attachment points, belly pan, body kit, body kits, bolt, bolts, Chevrolet, chevy cobalt, failure, fascia, fasteners, holes, inner fender, paint, PDF Download, pins, wheel
Labels: attachment points, belly pan, body kit, body kits, bolt, bolts, Chevrolet, chevy cobalt, failure, fascia, fasteners, holes, inner fender, paint, PDF Download, pins, wheel
All GRIP body kits need to be properly sanded and primed before painting, even if the part arrives pre-primed. Failure to properly prepare parts before painting can result in poor paint finish and adhesion. Please prefit parts before painting! Once a part has been painted or modified in any way it cannot be returned.
1: Look over vehicle before installing the body kit to make note of all attachment points on existing fascia. Since GRIP uses all existing attachment points, it is very important not to harm existing mounting holes and / or fasteners. Some fasteners that are drilled out cannot be reused. It is very important to use special care when removing the reusable fasteners from the panels since they will not be provided by GRIP. GRIP only provides non-reusable fasteners with its kits.
1: Look over vehicle before installing the body kit to make note of all attachment points on existing fascia. Since GRIP uses all existing attachment points, it is very important not to harm existing mounting holes and / or fasteners. Some fasteners that are drilled out cannot be reused. It is very important to use special care when removing the reusable fasteners from the panels since they will not be provided by GRIP. GRIP only provides non-reusable fasteners with its kits.
Subscribe to:
Posts (Atom)
