1953/54 Chevrolet RainGear Wiper System Installation Instructions

Pacific Western Design 53/54 Chevrolet Wiper System is designed to install in cars which are modified to use a 12- volt negative ground electrical system only and is not available for 6-volt(original)cars.

2002-2006 Honda CR-V Subwoofer Kit Installation Instructions

The subwoofer can not be installed with an under-seat CD changer.
Installation the Subwoofer to 2002-2006 CRV:
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Remove the two screws that fasten the bottom of the center panel.
4. Pull the center panel out toward you to release the six clips, unplug the vehicle connector from the hazard switch, and remove the center panel. Be careful care not to damage the clips.

Acura/Honda Car2PC-HON1 adapter for Car PC / laptop integration into car stereo

Preparation
1. Turn off car engine and remove key from ignition
2. Un-mount your radio from the dash in order to get access to the back side of the radio.
Adapter installation
3. Attach square 14 pins connector to the back of the Honda stereo.
4. Find a place where you can place Car2PC. In many cars there is enough room in the dash to place Car2PC.
Note: Make sure you mount Car2PC in a place with enough room so when you mount the car stereo back you do not break the adapter

Audi A6 C5 Instrument Panel Servicing

Component locations, overview 1 - Glove box Removing Page 68-1 2 - Driver's storage compartment Removing Page 68-7 3 - Steering column switch Removing Page 70-55 4 - Removing instrument cluster Repair Manual, Electrical Equipment, Repair Group 90; Servicing instrument cluster; Removing and installing instrument cluster 5 - Front section of center console Removing 68-28 6 - Center section of instrument panel Removing 68-31 7 - Reinforcing bracket for center section of instrument panel Removing Page 70-57 8 - Instrument panel end trim (left) Removing Page

2004-2006 Lexus RX330 Vehicle Wiring

WIRING INFORMATION: 2004 Lexus RX330: WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE RED Ignition Harness STARTER WIRE BLUE Ignition Harness SECOND STARTER WIRE WHITE Ignition Harness IGNITION WIRE PURPLE Ignition Harness SECOND IGNITION WIRE GREEN Ignition Harness ACCESSORY WIRE GRAY Ignition Harness POWER DOOR LOCK (-) BROWN At Module Inside Driver’s Door POWER DOOR UNLOCK (-) GRAY At Module Inside Driver’s Door Test power door lock wires using the key in the driver door. Unlock requires a double pulse PARKING LIGHTS (+) LIGHT GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) ORANGE Harness At Steering Column DRIVER DOOR TRIGGER (-) BLUE At Body ECU Behind Fuse Box PASSENGER DOOR TRIGGER (-) BLUE At Body ECU Behind Fuse Box RIGHT REAR DOOR TRIGGER (-) GRAY At Body ECU Behind Fuse Box LEFT REAR DOOR TRIGGER (-) BLACK Harness On Right Side Of Fuse Box REAR HATCH TRIGGER (-) WHITE/RED Harness In Driver’s Kick Panel

1993-96 Chevrolet Camaro Shaft and DIN Unit Provisions

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from the top of the driver's side knee bolster. Remove (2) 7mm screws from the bottom of the knee bolster. Open the glove box, remove (3) 7mm screws exposed on the right edge of the radio trim bezel and remove the bezel. Remove (2) 7mm screws securing the left side of the factory head unit and (1) 10mm nut securing the right. Slide the unit from the dash and disconnect the wiring. Cut and remove all mounting tabs on the Radio Housing EXCEPT tabs "A". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #5.

2006 Toyota Highlander Hybrid TVIP V2 (GBS Add On) Installation

1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Be careful not to touch the positive terminal. (b) Remove the air damper wire terminal from the bottom of the glove box. (Fig. 1-2) (1) Remove the clip securing the air damper wire terminal. (c) Remove the glove box. (Fig. 1-3) (1) Remove two stoppers securing the bottom of the glove box. (d) Remove the glove box inner cover. (Fig. 1-4) (1) Remove seven screws securing the cover. (2) Disconnect one connector. (e) Remove the passenger side panel. (Fig. 1-5) (1) Remove two clips securing the cover.

Toyota 4Runner, Highlander Trailer Wire Harness Service Bulletin

Beginning in 2000, the accessory trailer wire harness supplier was changed and a new design was adopted which incorporated in–line fuses in the tow wire harness in addition to the vehicle fuse. This bulletin identifies the fuse location to supplement dealer diagnostics troubleshooting. In the future please reference the accessory trailer wire harness Owner’s Guide for the vehicle specific diagnostic procedures. As a general note please place the towing wire harness Owner’s Guide in glove box after every DIO installation.

1995 Buick Regal V6-231 3.8L VIN L SFI - HVAC Blower Motor

HVAC Blower Motor Noise/Vibration
(Install New Blower Motor Assembly and/or VP Lower Compartment Access Hole Cover)
Models:
1995-96 Buick Regal
1995-96 Oldsmobile Cutlass Supreme
1994-96 Pontiac Grand Prix
Condition
Some owners may comment on noise and/or vibration from the HVAC blower motor.
This noise/vibration may be due to the blower motor being out of balance, or contents
(i.e. tissues, papers, etc.) in the instrument panel (I/P) lower compartment being drawn
into the blower motor assembly through the re-circulation door during MAX A/C mode.

Audi Gateway 500 with Dual FOT Installation

Installation of GATEWAY 500 unit Dual FOT
For All Audi vehicles: A good location to mount the GATEWAY 500 unit is at the CD Changer behind the glove box. If the vehicle is equipped with the in-dash CD Changer, install the GATEWAY 500 unit behind it. Interfacing in the MOST optical ring should be done as shown in the installation guide.
For All Audi vehicles NOT equipped with a factory CD Changer, the GATEWAY 500 interface shall be integrated into the optical MOST ring at the output of the head unit.
For All Audi vehicles equipped with a factory CD Changer, the GATEWAY 500 interface shall be installed at the factory CD Changer location