06 Chevrolet Aveo/Wave Cruise Control Installation Instructions

INSTALLATION
1) Remove knee panel under steering column, then remove (6) 10mm screws to release steel panel.
2) Remove lower steering column cover and driver side kick panel.
3) Connect the Red Cruise Harness Wire to Pink 12v Ignition Vehicle Wire behind fuse.
4) Connect the Black Cruise Harness Wire to Black Wire/Position 87 of 4

Honda CR-V DVD Navigation Attachment

DVD AVN Navigation Unit P/N: 08A40-1J6-100
Wire Harness Routing Precaution
Disconnect the connectors and terminals by holding them. Do not pull the harness to disconnect the connector.
Do not pull the harness with force. it will damage the har ness.
Cut off the excess of the wire ties.
Connect the connectors and terminals securely until they lock.
Reinstall the connectors to the corresponding stays whenever they are removed. After operation, check that the connectors are installed on the stays securely and not loose or come out of the stays.

1991-1996 Ford Escort Radio Replacement

STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.

2004-05 Chevy Colorado Prerunner Rear Bumper Installation

This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.

Transponder Bypass for Honda ET Acura (2 programmable modes)

You must use the Black key to complete the programming procedure. Programming : Keep the programming button pressed down while inserting the wire harness into connector of the HONDA-DA. Release the programming button once the LED turn ON. Turn the Ignition to the ON position. The number of LED flashes indicates the mode. (I.e. Mode 1 = 1 Flash) Press the programming button to switch between modes 1, 2 and 3. (Mode 3 is future use) Once the mode is selected, turn the ignition key to OFF position. Turn the IGNITION key to the ON position once again. The LED will illuminate. The module is now programmed. Turn the key to the OFF position and remove it, start the vehicle using the remote starter to insure functionality.

2004-2006 Lexus RX330 Vehicle Wiring

WIRING INFORMATION: 2004 Lexus RX330: WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE RED Ignition Harness STARTER WIRE BLUE Ignition Harness SECOND STARTER WIRE WHITE Ignition Harness IGNITION WIRE PURPLE Ignition Harness SECOND IGNITION WIRE GREEN Ignition Harness ACCESSORY WIRE GRAY Ignition Harness POWER DOOR LOCK (-) BROWN At Module Inside Driver’s Door POWER DOOR UNLOCK (-) GRAY At Module Inside Driver’s Door Test power door lock wires using the key in the driver door. Unlock requires a double pulse PARKING LIGHTS (+) LIGHT GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) ORANGE Harness At Steering Column DRIVER DOOR TRIGGER (-) BLUE At Body ECU Behind Fuse Box PASSENGER DOOR TRIGGER (-) BLUE At Body ECU Behind Fuse Box RIGHT REAR DOOR TRIGGER (-) GRAY At Body ECU Behind Fuse Box LEFT REAR DOOR TRIGGER (-) BLACK Harness On Right Side Of Fuse Box REAR HATCH TRIGGER (-) WHITE/RED Harness In Driver’s Kick Panel

2004-2006 Chevy Colorado Brute Force Intake System Installation

Getting Started
a) Make sure vehicle is parked on a level surface. Set parking brake.
b) Disconnect negative battery terminal from the battery.
c) If engine has run within the past two hours, let it cool down.
Removal of the stock intake system.
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process.

1983-1986 Toyota Radio Wire Harnesses

Note: using an optional snap on wire harness adapter will simplify the wiring. Most snap on wire harness adapters have already converted and color coded the wires from the auto makers in dash wire harness to match typical aftermarket radio wire colors. ** The wire colors listed in the chart above are typical for these vehicles during these years but may not be the exact colors for this vehicle. This is another reason to use a snap on wire harness adapter. **

Toyota Wire Harness Repair Kit "B"

The new Wire Harness Repair Kit “B” has been released as an essential Special Service Tool (SST)
to supplement the original Wire Harness Repair Kit. This kit holds an initial supply of 21 new type
electrical terminals and connectors as well as the necessary supplies and small tools for most electrical repairs.

2007 Toyota Camry Hybrid Sirius XM Radio Satellite Installation

Cable Routing and Installation (a) Install and route the tuner cable from the center cluster and along the front support bar. (Fig. 3-1) (b) Provide sufficient cable slack to connect to the tuner, and then secure the cable to the existing wire harness with lock tie. Cut excess off lock tie. Connect wire harness to head unit. (c) Using lock ties attach to existing W /H. Trim lock tie excess. (Fig. 3-2) (d) Route to the existing clamps. (Fig. 3-2) (f) Route the cable as shown and secure with lock tie. Trim lock tie excess. (Fig. 3-4) (g) Route the tuner cable under the rear passenger seat and secure with cushion tape. (Fig. 3-5) NOTE:Clean the area for the cushion tape with the approved cleaner.

1996-2000 Honda Civic EX, GX, LX Sedan Signal Mirror Installation Instructions

Door panel removal
1. Open door and lower window.
2. Remove screw from center of armrest and remove armrest from door.
3. Disconnect wire from behind window control panel.
4. Remove screw from behind door handle and remove door handle cover.
5. Disconnect wire from behind door handle cover.
6. Remove speaker cover.

1996-2000 Honda Civic Vertical Door Installation

1) Disconnect the battery. 2) Remove fender: Remove all Phillip’s screws from the wheel well. Remove (1) 12mm bolt to loosen the bumper. Once the 12mm bolt has been removed pull on the bumper and remove (2) 8mm bolts from behind the bumper. Remove (3) 8mm bolts form the top of the fender. Remove (2) 8mm bolts from the bottom of the fender by the door. Remove (1) 8mm bolt holding the fender. At this point you should be able to remove the fender. 3) Remove the door catch: Open the door and remove (1) 10mm bolt from the body and (2) 10mm from the door. Push the door catch inside the door. 4) Gaining wire slack: Remove foot trim, under it you will find (2) wire harness use the

2006 Toyota Corolla Engine Control Module Removal and Installation

REPLACEMENT 1. DISCONNECT BATTERY NEGATIVE TERMINAL
2. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
a. Remove the screw from the glove compartment door stoppers.
b. Deform the upper part of the glove compartment door assembly to release the stoppers.
c. Pull the glove compartment door assembly upward to remove it.
3. REMOVE ECM
a. Remove the 2 clips using a clip remover, then open the cover.
b. Disconnect the 4 ECM connectors.

Chrysler-Dodge Radio Wire Harnesses Installation

If your original radio had a braided strap bolted to the rear of the radio.
TIP: Crimp a ring terminal to the new radios ground wire and insert a bolt through both connectors to connect the ring terminal of the braided ground wire to the ring terminal attached to the new radios ground wire.
If your original radio had a plastic connector containing a single wire plugged into the rear of the radio.
TIP: Crimp a male tab spade to the new radios ground wire. Slide it into the female tab spade connector that had originally snapped into the rear of the factory radio.

1984-1991 Cadillac El Dorado Radio Install

Wiring Instructions: The power and speaker wires needed to connect the new radio are attached to the connector of the wire harness located inside the vehicles dash. The Install Doctor STRONGLY recommends using an optional snap on wire harness that is specifically designed to snap into the vehicles dash wire harness connector. This will keep you from cutting the vehicles wires. This optional snap on wire harness will have wires on the opposite side of the connector that will allow you to splice these wires to the new radios wires. The only other option is to cut off the vehicles dash wire harness connector and splice the new radios wires directly to these wires. The optional snap on wire harness takes all the guess work out of trying to figure out what each wire is in the vehicles dash wire harness. The optional snap on wire harness tell you what each wire is.

OS-2CTS Cadillac CTS/SRX Radio Replacement Installation Instructions

Step 1. Pre wire the RAD-18 wire harness to the aftermarket stereo wire harness. If the aftermarket stereo has a mute wire, cut the brown wire as close as possible to pin #16 of the RAD-18 harness and connect this mute output wire to the stereo’s mute wire. The amp remote wire (blue/white) must be connected to the stereo’s remote wire.
Step 2. Connect the black 16 pin and the red 20 pin harness to the factory radio harnesses. Connect the OS-CTS wire harness into the OS-2CTS interface.