INSTALLATION
1) Remove knee panel under steering column, then remove (6) 10mm screws to release steel panel.
2) Remove lower steering column cover and driver side kick panel.
3) Connect the Red Cruise Harness Wire to Pink 12v Ignition Vehicle Wire behind fuse.
4) Connect the Black Cruise Harness Wire to Black Wire/Position 87 of 4
Showing posts with label tape measure. Show all posts
Showing posts with label tape measure. Show all posts
Monday, January 3, 2011
06 Chevrolet Aveo/Wave Cruise Control Installation Instructions
3:32 AM by onesecond
·
0
comments
Labels: 10mm, 5mm, aveo, Chevrolet, chevrolet aveo, cruise control module, fuse, knee panel, lettering, metal bracket, pin connector, screws, shroud, side kick panel, steel panel, steering column, switch harness, tape measure, wire harness, yellow wires
Labels: 10mm, 5mm, aveo, Chevrolet, chevrolet aveo, cruise control module, fuse, knee panel, lettering, metal bracket, pin connector, screws, shroud, side kick panel, steel panel, steering column, switch harness, tape measure, wire harness, yellow wires
Friday, June 11, 2010
2010+ Kia Forte Koup QuickLIFT Installation Guide
2:36 AM by onesecond
·
0
comments
Labels: ball studs, brackets, center punch, drill bits, hammer, hinge, Kia, marker, masking tape, permanent marker, quicklift, rt, ruler, step 2, step 3, step source, tape measure
Labels: ball studs, brackets, center punch, drill bits, hammer, hinge, Kia, marker, masking tape, permanent marker, quicklift, rt, ruler, step 2, step 3, step source, tape measure
Step 1 - Unpack QuickLIFT system and verify contents. Remove all items from the packing tube. You should have the following before beginning: * (2) Gas springs (RT-QL-200-4A) - Be sure to cycle them a few times before installing. * (4) 3/16" multi-grip #1 rivets (used on hood brackets) * (2) ball-studs and washers * Printed Color Instructions
Sunday, May 30, 2010
Automatic Retracting Running Board Installation Instructions
3:51 AM by onesecond
·
0
comments
Labels: carpet, drill holes, drill template, fasteners, flat screwdriver, kick panel, kick plate, PDF Download, pilot hole, rear arm, running board, s driver, sheet metal screws, straight edge, tape measure, vertical line, vise grips, wiring harness
Labels: carpet, drill holes, drill template, fasteners, flat screwdriver, kick panel, kick plate, PDF Download, pilot hole, rear arm, running board, s driver, sheet metal screws, straight edge, tape measure, vertical line, vise grips, wiring harness
Drill Holes for Rear Arm
Locate the Drill Template in the parts kit. Place it along the sill 1/16" in front of the rear sill drain. Use vise grips to secure the Template to the sill. Drill a 1/8" pilot hole at each location in the Template. Remove the Template and drill the holes out to 21/64".
Drill Holes for Front Arm
Most Vehicles
Clamp the Drill Template to the pinch weld 1/8" behind the front mounting tab. Drill a 1/8" pilot hole at each location in the Template. Remove the Template and drill the holes out to 21/64". SUV's – Driver’s Side Only Clamp the Drill Template 1/8" in front of the sill drain. Then drill the holes as above.
Locate the Drill Template in the parts kit. Place it along the sill 1/16" in front of the rear sill drain. Use vise grips to secure the Template to the sill. Drill a 1/8" pilot hole at each location in the Template. Remove the Template and drill the holes out to 21/64".
Drill Holes for Front Arm
Most Vehicles
Clamp the Drill Template to the pinch weld 1/8" behind the front mounting tab. Drill a 1/8" pilot hole at each location in the Template. Remove the Template and drill the holes out to 21/64". SUV's – Driver’s Side Only Clamp the Drill Template 1/8" in front of the sill drain. Then drill the holes as above.
Subscribe to:
Posts (Atom)
