Installation note:
• Be careful not to damage the body paint finish.
• This interior trim kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
1. Using isopropyl alchohol on a shop towel, clean the area where the right outlet trim will attach.
2. Peel back one inch from the end of the 13 adhesive backings shown, and attach them to the front of the right outlet panel with masking tape. Remove and discard the three remaining adhesive backings from the trim.
Showing posts with label masking tape. Show all posts
Showing posts with label masking tape. Show all posts
Monday, November 15, 2010
2008 Honda CR-V Interior Panel Set P/N 08Z03-SWA-100A Installation
12:04 AM by onesecond
·
0
comments
Labels: alchohol, alcohol, ambient air temperature, body paint, Honda, honda cr v, interior panel, masking tape, palm of your hand, shop towel, swa
Labels: alchohol, alcohol, ambient air temperature, body paint, Honda, honda cr v, interior panel, masking tape, palm of your hand, shop towel, swa
Tuesday, November 9, 2010
2005 Honda CR-V Door Visors P/N 08R04-S9A-101
3:47 AM by onesecond
·
1 comments
Labels: 2005 honda cr v, alcohol, ambient air temperature, brackets, glass run, Honda, honda cr v, masking tape, mirror base, paint, palm of your hand, rear end, sash, shock, shop towel
Labels: 2005 honda cr v, alcohol, ambient air temperature, brackets, glass run, Honda, honda cr v, masking tape, mirror base, paint, palm of your hand, rear end, sash, shock, shop towel
Installation Door Visors on Honda CR-V 2005:
NOTE: • These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors.
• Be careful not to damage the paint finish or glass run channels when installing the door visors.
• Handle the door visors with care. They are not designed to absorb shock or impact.
• This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours.
NOTE: • These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors.
• Be careful not to damage the paint finish or glass run channels when installing the door visors.
• Handle the door visors with care. They are not designed to absorb shock or impact.
• This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours.
Sunday, June 20, 2010
Vauxhall Cavalier/Opel 4 x 4 Transfer Box Installation
1:45 AM by onesecond
·
0
comments
Labels: bolts, caution, fig 1a, flange, gearbox, grease, heavy duty gloves, ingress, masking tape, mounting bolt, opel, splined shafts, straight angle, temp sensor, temperature sensor, torsion bar, trolley jack, txb, unwanted material, vauxhall cavalier
Labels: bolts, caution, fig 1a, flange, gearbox, grease, heavy duty gloves, ingress, masking tape, mounting bolt, opel, splined shafts, straight angle, temp sensor, temperature sensor, torsion bar, trolley jack, txb, unwanted material, vauxhall cavalier
This procedure assumes the removal procedure has been read and/or followed. CAUTION: If you followed the removal procedure, the gearbox may NOT have any oil in it - do not forget. 500. Inspect the txb (Transfer box) before reinstalling, Clean off any excess jointing compound.
501. Lightly apply grease to the flange of the txb to gearbox coupling (two visible splined shafts), and apply the rubber 'O' ring to the flange.
502. Apply masking tape (Fig.1B) or similar to the fluid coupling and the txb breather/filler connections to prevent ingress of unwanted material while installing the txb.
501. Lightly apply grease to the flange of the txb to gearbox coupling (two visible splined shafts), and apply the rubber 'O' ring to the flange.
502. Apply masking tape (Fig.1B) or similar to the fluid coupling and the txb breather/filler connections to prevent ingress of unwanted material while installing the txb.
Friday, June 11, 2010
2010+ Kia Forte Koup QuickLIFT Installation Guide
2:36 AM by onesecond
·
0
comments
Labels: ball studs, brackets, center punch, drill bits, hammer, hinge, Kia, marker, masking tape, permanent marker, quicklift, rt, ruler, step 2, step 3, step source, tape measure
Labels: ball studs, brackets, center punch, drill bits, hammer, hinge, Kia, marker, masking tape, permanent marker, quicklift, rt, ruler, step 2, step 3, step source, tape measure
Step 1 - Unpack QuickLIFT system and verify contents. Remove all items from the packing tube. You should have the following before beginning: * (2) Gas springs (RT-QL-200-4A) - Be sure to cycle them a few times before installing. * (4) 3/16" multi-grip #1 rivets (used on hood brackets) * (2) ball-studs and washers * Printed Color Instructions
Thursday, May 6, 2010
Chrysler Pasifica DVD Rear Seat Video System Installation
3:31 AM by onesecond
·
0
comments
Labels: access panel, bezel, Chrysler, chrysler pasifica, component removal, cubby, dotted lines, masking tape, metal trim, negative battery cable, phillips screw, phillips screws, pillar, radio four, rear seat, t20, template instructions, tie straps, utility knife, video system
Labels: access panel, bezel, Chrysler, chrysler pasifica, component removal, cubby, dotted lines, masking tape, metal trim, negative battery cable, phillips screw, phillips screws, pillar, radio four, rear seat, t20, template instructions, tie straps, utility knife, video system
A – Interior Trim Panel and Component Removal:
1) Disconnect and isolate negative battery cable.
2) Detach the center console shift bezel.
3) Remove ignition key bezel.
4) Remove left and right I/P center bezels using a non-metal trim stick.
5) Disconnect and remove the CD/DVD player or cubby bin (four phillips screws).
6) Disconnect and remove the radio (four phillips screws).
1) Disconnect and isolate negative battery cable.
2) Detach the center console shift bezel.
3) Remove ignition key bezel.
4) Remove left and right I/P center bezels using a non-metal trim stick.
5) Disconnect and remove the CD/DVD player or cubby bin (four phillips screws).
6) Disconnect and remove the radio (four phillips screws).
Subscribe to:
Posts (Atom)
