Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure all airbag systems have been disabled for your safety.
Showing posts with label mounting bolt. Show all posts
Showing posts with label mounting bolt. Show all posts
Wednesday, January 26, 2011
Chevrolet Silverado Rear Backup Camera System
5:48 PM by onesecond
·
0
comments
Labels: Chevrolet, chevrolet silverado, latch handle, mounting bolt, negative battery cable, punch mark, surface, tailgate
Labels: Chevrolet, chevrolet silverado, latch handle, mounting bolt, negative battery cable, punch mark, surface, tailgate
Thursday, December 30, 2010
Chevrolet Silverado Rear Vision System Nav Display Installation Instructions
1:35 AM by onesecond
·
0
comments
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
Sunday, June 20, 2010
Vauxhall Cavalier/Opel 4 x 4 Transfer Box Installation
1:45 AM by onesecond
·
0
comments
Labels: bolts, caution, fig 1a, flange, gearbox, grease, heavy duty gloves, ingress, masking tape, mounting bolt, opel, splined shafts, straight angle, temp sensor, temperature sensor, torsion bar, trolley jack, txb, unwanted material, vauxhall cavalier
Labels: bolts, caution, fig 1a, flange, gearbox, grease, heavy duty gloves, ingress, masking tape, mounting bolt, opel, splined shafts, straight angle, temp sensor, temperature sensor, torsion bar, trolley jack, txb, unwanted material, vauxhall cavalier
This procedure assumes the removal procedure has been read and/or followed. CAUTION: If you followed the removal procedure, the gearbox may NOT have any oil in it - do not forget. 500. Inspect the txb (Transfer box) before reinstalling, Clean off any excess jointing compound.
501. Lightly apply grease to the flange of the txb to gearbox coupling (two visible splined shafts), and apply the rubber 'O' ring to the flange.
502. Apply masking tape (Fig.1B) or similar to the fluid coupling and the txb breather/filler connections to prevent ingress of unwanted material while installing the txb.
501. Lightly apply grease to the flange of the txb to gearbox coupling (two visible splined shafts), and apply the rubber 'O' ring to the flange.
502. Apply masking tape (Fig.1B) or similar to the fluid coupling and the txb breather/filler connections to prevent ingress of unwanted material while installing the txb.
Sunday, May 9, 2010
Small Block Chrysler 727 to GM DRCE Engine Adaptor Installation
3:54 AM by onesecond
·
0
comments
Labels: adaptor plate, bolts, Chrysler, decal, dowels, drce, GM, head cap, mounting bolt, mountings, necessary step, PDF Download, sfi, socket head cap screw, socket head cap screws, step 1, torque, torque converter, transmission case
Labels: adaptor plate, bolts, Chrysler, decal, dowels, drce, GM, head cap, mounting bolt, mountings, necessary step, PDF Download, sfi, socket head cap screw, socket head cap screws, step 1, torque, torque converter, transmission case
This Adapter Plate is designed to cover Flexplate only. To protect the Bellhousing area we suggest using the CSR Shield #834. Tech Officials will require a transmission shield. Care must be taken to ensure that this bolt does not Interfere with the Starter Bolt (binding can occur). Starter mountings can vary on DRC Engines. Contact us for Starter Reduction Adaptor Blocks.
Subscribe to:
Posts (Atom)
