Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
Showing posts with label step 8. Show all posts
Showing posts with label step 8. Show all posts
Thursday, December 30, 2010
Chevrolet Silverado Rear Vision System Nav Display Installation Instructions
1:35 AM by onesecond
·
0
comments
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Saturday, June 5, 2010
2005+ Toyota Tacoma Service Guide & Vehicle History
11:02 PM by onesecond
·
0
comments
Labels: 2005 toyota tacoma, button down, door locks, interval 1, intervals, odometer, odometer button, remote keyless entry, reset 3, step 8, Toyota, toyota tacoma, transmitters, vehicle history, zeros
Labels: 2005 toyota tacoma, button down, door locks, interval 1, intervals, odometer, odometer button, remote keyless entry, reset 3, step 8, Toyota, toyota tacoma, transmitters, vehicle history, zeros
Remote Keyless Entry Reprogramming The vehicle should meet the following conditions before proceeding; *The key is NOT in the ignition *Driver’s door is OPEN (The others are CLOSED) *Drivers door UNLOCKED 1) INSERT & REMOVE key from ignition cylinder TWICE within 5sec 2) CLOSE and OPEN the driver’s door TWICE within 40sec 3) INSERT and REMOVE the key into the ignition cylinder 4) CLOSE and OPEN the driver’s door TWICE within 40 seconds 5) INSERT the key in the ignition and CLOSE the driver’s door 6) Turn the ignition switch from LOCK to ON and back to LOCK at 1sec Intervals "2" times to enter REWRITE MODE 7) REMOVE the key from the ignition (The door locks are cycled
Monday, May 24, 2010
2004-2006 Ford F-150 Liquid Solid Billet Door Handle Instruction
11:55 PM by onesecond
·
0
comments
Labels: 2 step, 2006 ford f 150, advanced auto, auto body, billet, door handle, door handles, Ford, ford f 150, free source, hex head screws, kit contents, paneling, plastic mesh, plastic plugs, screw driver, step 2, step 8, wiring harness, wiring harnesses
Labels: 2 step, 2006 ford f 150, advanced auto, auto body, billet, door handle, door handles, Ford, ford f 150, free source, hex head screws, kit contents, paneling, plastic mesh, plastic plugs, screw driver, step 2, step 8, wiring harness, wiring harnesses
The installation of the replacement door handles are for persons with advanced auto-body skills and is recommended to have them professionally installed.
A. Pre-installation Preparation
Step 1: Verify kit contents.
Step 2: Remove the door handles from the box.
Step 3: Make sure the window is up and the door is unlocked.
A. Pre-installation Preparation
Step 1: Verify kit contents.
Step 2: Remove the door handles from the box.
Step 3: Make sure the window is up and the door is unlocked.
Friday, May 14, 2010
U-Cut-To-Fit GM & Chrysler Speedometer Cable Kit Installation Instructions
3:47 AM by onesecond
·
0
comments
Labels: bottoms, cable kit, car source, Chrysler, debur, exhaust pipes, failure, figure 1, GM, grease, hammer, PDF Download, pliers, screw, solid surface, speedometer cable, step 2, step 6, step 8, transmission gear
Labels: bottoms, cable kit, car source, Chrysler, debur, exhaust pipes, failure, figure 1, GM, grease, hammer, PDF Download, pliers, screw, solid surface, speedometer cable, step 2, step 6, step 8, transmission gear
U-Cut-To-Fit Speedometer Cable Kit Installation
Step 1: Install outer housing to speedometer and route housing to transmission, making sure to keep away from exhaust pipes.
Step 2: Hold housing up to transmission to determine length and mark a cut line. Remove housing from vehicle and cut housing at the cut line.
Step 3: After cutting housing, install end of housing into GM or Chrysler trans end fitting. Figure 1 Slide housing nut up and tighten until housing is locked into fitting.
Note: Do Not over tighten nut as it will result in fitting failure.
Step 1: Install outer housing to speedometer and route housing to transmission, making sure to keep away from exhaust pipes.
Step 2: Hold housing up to transmission to determine length and mark a cut line. Remove housing from vehicle and cut housing at the cut line.
Step 3: After cutting housing, install end of housing into GM or Chrysler trans end fitting. Figure 1 Slide housing nut up and tighten until housing is locked into fitting.
Note: Do Not over tighten nut as it will result in fitting failure.
Monday, March 8, 2010
2007-2008 BMW E82/88 135i Intake kit Installation Instructions
5:41 PM by onesecond
·
0
comments
Labels: 5b, air filters, battery cable, BMW, clamps, fender, hoses, nut driver, PDF Download, pliers, push down, radiator, rubber edge, rubber grommets, screw, step 1, step 3, step 8, stock intake, vacuum line
Labels: 5b, air filters, battery cable, BMW, clamps, fender, hoses, nut driver, PDF Download, pliers, push down, radiator, rubber edge, rubber grommets, screw, step 1, step 3, step 8, stock intake, vacuum line
Step 1: Complete Stock Intake.
Step 2: Disconnect vacuum line and pull back.
Step 3: Unclip upper half of air box to remove lid and filter.
Step 4: Pull back rubber mount attached to battery cable. Use pliers if necessary. This will allow stock clamp to be loosened. (To be done in step 5B.)
Step 5: A) Loosen clamp closest to the radiator with 1/4” nut driver. B) Loosen clamp closest to fire wall with 1/4” nut driver. Leave clamps in position.
Step 2: Disconnect vacuum line and pull back.
Step 3: Unclip upper half of air box to remove lid and filter.
Step 4: Pull back rubber mount attached to battery cable. Use pliers if necessary. This will allow stock clamp to be loosened. (To be done in step 5B.)
Step 5: A) Loosen clamp closest to the radiator with 1/4” nut driver. B) Loosen clamp closest to fire wall with 1/4” nut driver. Leave clamps in position.
Subscribe to:
Posts (Atom)
