Chevrolet Van 97 & Up Sway Bar Installation

This bar was designed to replace your original equipment sway-bar. The diameter of the bar has been increased for more roll resistance; the contours of the bar may differ slightly, if some of the bends were not necessary. This kit may come with none, some or all of the hardware required to install the bar depending on the application. If hardware is not included with the kit, the hardware from the O.E. bar must be retained and re-used. If these parts are too worn to be re-used it will be necessary to obtain them from your O.E. parts dealer. If your car/truck was not equipped with O.E. bar, the installation of this bar may not be possible.

1996-1998 ACURA 3.5 RL w/o GPS Part Number AC-55-96 Instructions

STEP 1. Begin by inserting the hook tool underneath the right rear corner of the black trim bezel that surrounds the shifter lever. Pull upward to release one (1) plastic clip. Perform this same action in the remaining three (3) corners on the bezel, releasing three (3) more plastic clips. Slide the bezel over the shifter knob and disconnect all wiring. Set the bezel aside. Remove the wood grain trim bezel that surrounds the shifter. This bezel also has the ashtray integrated into it. Insert your hook tool underneath the right rear corner of this bezel and pull upward to release right rear clip. Insert the hook tool underneath the left rear cor- ner of the bezel and pull upward to release left rear clip. There are two more clips holding the bezel in place located in front of the shifter just behind the ashtray. Insert your hook tool between the center console padding and the trim bezel on the right side of bezel. Pull upward to release clip. Perform this same action on the left side. Grasp the

1992-96 Toyota Camry Pro.Fit Part Number TY-50-92 Installation Instructions

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Pro.Fit logo and part number will be right side up and readable when installed.
TOOLS REQUIRED: #2 Phillips screwdriver, hook tool.
PARTS INCLUDED: Pro.Fit VSMTM, instructions.
LOCATION: To the right of the radio.

2010+ Kia Forte Koup QuickLIFT Installation Guide

Step 1 - Unpack QuickLIFT system and verify contents. Remove all items from the packing tube. You should have the following before beginning: * (2) Gas springs (RT-QL-200-4A) - Be sure to cycle them a few times before installing. * (4) 3/16" multi-grip #1 rivets (used on hood brackets) * (2) ball-studs and washers * Printed Color Instructions

2006 Mazda MX-5 Squeaking Noise Around Rear Center Console Lid

Some vehicles may exhibit a squeaking noise from around the rear center console lid area when driving on a rough road or turning corners at slow speeds. Torque of the rear center console lid striker screw is insufficient. The tightening process has been revised in production. Customers having this concern should have their vehicle repaired using the following repair procedure.

1999 Protege 1.6L Rattling Noise From Engine

APPLICABLE MODEL(S)/VINS
All 1999 Protege (1.6L) with VINs lower than JM1 BJ222* X0 140057.
All 1999 - 2000 Miata with (1.8L) VINs lower than JM1 NB353* Y0 155947.
DESCRIPTION A rattling noise may be heard from the engine when depressing the clutch or when revving the engine in neutral. In extreme cases, customers may experience noise at all times. This concern can be caused by improperly machined number 4 main cap of cylinder blocks which may result in premature wear of the thrust bearing. Customers having this concern should have their vehicle repaired using the following procedure.

2007 Honda Pilot EX Pinging, Rattling or Squealing During Light Acceleration

If you're viewing this service bulletin on ISIS and the computer has sound, click
on the image below to hear an example of how the noise may sound and see the
rpm levels it occurs at.
1. Drive the vehicle at low speeds (25 mph or less) under light throttle.
If you hear a ping, rattle, or squeal, go to step 3.
If you don't hear a ping, rattle, or squeal, go to step 2.

1992-95 Cadillac Eldorado & Seville Pro.Vit VSM Installation

STEP 1. Begin by removing the small black trim ring that surrounds the radio. Insert the hook tool behind the upper right corner of the trim ring and pull toward you to loosen the ring. Once the ring is loose, work the remaining three (3) corners of the trim ring loose. Set the trim ring aside. Turn the ignition to the “ON” position and shift the transmission into low gear. Just above the ashtray door, grasp the top section of the bezel that surrounds the transmission shifter and pull toward you to release two (2) clips. Insert the hook tool behind the right rear corner of the bezel just behind the shifter. Pull upward to release one (1) clip. Perform the same action in the left rear corner releasing one (1) more clip. Grasp the rear of the bezel and continue working loose two (2) clips on the left and right sides of the shifter. Work the bezel up and over the shifter knob and disconnect all wiring. Set the bezel aside.

2007-2008 BMW E82/88 135i Intake kit Installation Instructions

Step 1: Complete Stock Intake.
Step 2: Disconnect vacuum line and pull back.
Step 3: Unclip upper half of air box to remove lid and filter.
Step 4: Pull back rubber mount attached to battery cable. Use pliers if necessary. This will allow stock clamp to be loosened. (To be done in step 5B.)
Step 5: A) Loosen clamp closest to the radiator with 1/4” nut driver. B) Loosen clamp closest to fire wall with 1/4” nut driver. Leave clamps in position.