2005-06 HONDA CRV Grill/ Brush Guard Part #6049

Procedure installing the Grill to Honda CRV
1. Remove the plastic rivets securing the plastic guard located underneath the vehicle in order to install the front bar.
2. Start with the passenger side assembly, postion one of the 7/16 nut plates behind the cross member opening and align the 7/16 nut plate wit the two matching holes in the frame rail. Fasten the frame brackets to the bottom cross member as shown in the illustration using the 7/16 x 1 ¼ hex bolts, 7/16 washers, 5/16 self tapping bolt and 5/16 washers. Note: Do not over tighten 5/16 x 1 self tapping bolt as it might strip threads.

Acura RSX Heated Mirror Installation Instructions

Heated Mirrors: I have installed heated mirrors in the US model. Here's what I did; but before installing make sure you read through the entire instructions so you have a good idea what is expected.
Tools: Here are some of the tools you will need. If you don’t have most of these or know how to use them, STOP. This is not for you.
Disclaimer: These instructions are for reference only. Anyone who uses these instructions agrees to hold the author harmless. It is the users’ responsibility to verify the suitability of these reference instructions to their vehicle.

Cabin Air Filters Application & Installation Guide

Ford Focus from Model Year 2000.
1. • Stop windshield wipers in up position. • Open hood
2. • Remove the cap on screw in center of cowl cover. • Unscrew half way & pull out fitting. • Unsnap 3 clips on front edge of cover & remove cover.
3. • Either a filter or screen is visible under louver. Flip out front edge of housing & remove the filter or plate.
4. • Replace with a clean Cabin Air Filter. Make sure the arrows on the filter are facing up. • Reclip front of housing in place & replace the cowl cover.

1997 Acura RL V6-3474cc 3.5L Dashboard / Instrument Panel Service Repair

Dashboard Component Removal/Installation
CAUTION: When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
NOTE: Take care not to scratch the dashboard and related parts.
Instrument panel:
1. Remove the center air vent.
2. Remove the climate control unit and audio unit as an assembly ('96 - 98 models, '99 - 04 models). NOTE: Do not disconnect the connectors.
3. Remove the dashboard lower cover and driver's switch trim.
4. Remove the screws, detach the clips, then carefully pull out the instrument panel in the numbered sequence. Disconnect the connector, then remove it.

2006 Mazda MX-5 Squeaking Noise Around Rear Center Console Lid

Some vehicles may exhibit a squeaking noise from around the rear center console lid area when driving on a rough road or turning corners at slow speeds. Torque of the rear center console lid striker screw is insufficient. The tightening process has been revised in production. Customers having this concern should have their vehicle repaired using the following repair procedure.

1996-2000 Honda Civic EX, GX, LX Sedan Signal Mirror Installation Instructions

Door panel removal
1. Open door and lower window.
2. Remove screw from center of armrest and remove armrest from door.
3. Disconnect wire from behind window control panel.
4. Remove screw from behind door handle and remove door handle cover.
5. Disconnect wire from behind door handle cover.
6. Remove speaker cover.

96-00 Honda Civil Door Panel Removal & Installation

Remove the screw from behind the interior door handle Slide out the door handle trim as shown Removing the door panel from the passenger side door View of the inside of the door, panel removed 1. Remove the screw from the door handle trim. 2. Slide the handle assembly forward and out to access the lock rod clip. 3. Release the clip 4. Disconnect the door lock switch 5. Remove the door opener handle assembly. 6. Carefully pry at the small opening on the bottom of the speaker grill. 7. Remove the speaker grille. 8. Remove the speaker mounting screws. 9. Detach the electrical connector and remove the speaker. 10. Remove the screws in the armrest. 11. Remove the center from the trim clip at the upper front of the door panel and remove the clip. 12. Using a suitable trim panel removal tool, unsnap the door panel from the door frame. 13. Carefully lift the door panel up and away from the door frame. To install: 14. Installation is the reverse of the removal procedure.

1993 Taurus/Sable Bumpers Removal and Installation

Bumpers Refer to the following illustrations when performing Removal and Installation procedures on the front and rear bumper assemblies. CAUTION: Never apply excessive heat to bumper surface. Heat could cause distortion of the bumper. CAUTION: When collecting exhaust fumes in service area, never attach a metal collector to the exhaust tail pipe because the heat could damage the bumper.

2006 Toyota Corolla Engine Control Module Removal and Installation

REPLACEMENT 1. DISCONNECT BATTERY NEGATIVE TERMINAL
2. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
a. Remove the screw from the glove compartment door stoppers.
b. Deform the upper part of the glove compartment door assembly to release the stoppers.
c. Pull the glove compartment door assembly upward to remove it.
3. REMOVE ECM
a. Remove the 2 clips using a clip remover, then open the cover.
b. Disconnect the 4 ECM connectors.

1992-95 Cadillac Eldorado & Seville Pro.Vit VSM Installation

STEP 1. Begin by removing the small black trim ring that surrounds the radio. Insert the hook tool behind the upper right corner of the trim ring and pull toward you to loosen the ring. Once the ring is loose, work the remaining three (3) corners of the trim ring loose. Set the trim ring aside. Turn the ignition to the “ON” position and shift the transmission into low gear. Just above the ashtray door, grasp the top section of the bezel that surrounds the transmission shifter and pull toward you to release two (2) clips. Insert the hook tool behind the right rear corner of the bezel just behind the shifter. Pull upward to release one (1) clip. Perform the same action in the left rear corner releasing one (1) more clip. Grasp the rear of the bezel and continue working loose two (2) clips on the left and right sides of the shifter. Work the bezel up and over the shifter knob and disconnect all wiring. Set the bezel aside.

07-Up Chevy Tahoe LED Upper Quarter Panel Light

Your new IPCW LED Upper Quarter Panel Lights are quality-made products that will work beautifully on your vehicle. Please refer to the pictures below for installation instructions.
Remove the screws in Figure A with a Phillips screwdriver. Untwist the sockets, then gently slide out the tail light.
After the tail light is removed. remove the screw in Figure B.
Remove the screw in Figure C to remove the Upper Quarter panel.
Gently slide out the stock Upper Quarter Panel.

Front Connected 63 Fuse Fitting

Method of Cabling Front connected fuse fittings
1. Remove red nylon insulating shroud to release cable sleeve.
2. Remove cable sleeve.
3. Fit cable sleeve over cable.
4. Fit conductor into fuse base terminal and tighten cable clamping screw to secure. If flexible cables are used, their relatively fine strands may be given increased protection by the use of thin wall copper ferrules over the conductor.
The following should be taken into account:

2001 Mercedes Benz E 320 Sedan V6-3.2L Door Liner on Rear Door Remove/Install

Removing/Installing
1. Press of handle recess (3) using assembly wedge
2. Unscrew screw (4) in the area of the interior door control
3. Unclip cover (11) and unscrew screw (12) With code 293 (rear side airbag)
4. Unscrew screw (1) on lock escutcheon (2) and remove lock escutcheon (2) downwards
5. Press of cover (5) under armrest and unscrew screw (6)

U-Cut-To-Fit GM & Chrysler Speedometer Cable Kit Installation Instructions

U-Cut-To-Fit Speedometer Cable Kit Installation
Step 1: Install outer housing to speedometer and route housing to transmission, making sure to keep away from exhaust pipes.
Step 2: Hold housing up to transmission to determine length and mark a cut line. Remove housing from vehicle and cut housing at the cut line.
Step 3: After cutting housing, install end of housing into GM or Chrysler trans end fitting. Figure 1 Slide housing nut up and tighten until housing is locked into fitting.
Note: Do Not over tighten nut as it will result in fitting failure.

GM / Chevy / Cadillac (GMT800) Telescopic Trailer Tow Mirror Fitting Instructions

Made by the world’s largest manufacturer of exterior mirrors, the Telescopic Trailer Tow Mirror combines great looking aerodynamic styling with the toughness only a company like Schefenacker can produce. You’ve chosen one of the hottest new products in the past few years! Its interchangeable covers mean you can personalize the looks that suit you and your pick up, and a wide range of options mean you can have the right equipment for the right job.

1984-1991 Cadillac El Dorado Radio Install

Wiring Instructions: The power and speaker wires needed to connect the new radio are attached to the connector of the wire harness located inside the vehicles dash. The Install Doctor STRONGLY recommends using an optional snap on wire harness that is specifically designed to snap into the vehicles dash wire harness connector. This will keep you from cutting the vehicles wires. This optional snap on wire harness will have wires on the opposite side of the connector that will allow you to splice these wires to the new radios wires. The only other option is to cut off the vehicles dash wire harness connector and splice the new radios wires directly to these wires. The optional snap on wire harness takes all the guess work out of trying to figure out what each wire is in the vehicles dash wire harness. The optional snap on wire harness tell you what each wire is.

DICE ipod BMW Z4 Installation

This “how to” guide installs the kit into a Z4 with no CD changer and a standard business cd (no sat nav), ipod location in the central compartment.
1: The kit
2: Disconnect battery with 10mm socket
3: Now it’s a bit of a pain, but to get easier access to centre console I removed the boot carpet. Use a large flat head screwdriver to remove the retaining screws on the left and the right hand side of the boot. You need to reach behind the carpet to hold the nut at the back.

Direction on how to install E-Open in to a BMW Z4

Please note the following:
1) This is for information ONLY; you take full responsibility for what you do. If you blow up your car, do not come yelling at me.
2) I did this install on a US spec 2005 BMW Z4. I do NOT know if it will work on BMW’s from other countries.
3) This install did NOT work because my Z4 already had an auto top down feature from BMW that is conflicting with the E-Open. In order to get this to work in my car I have to find out how to disable the internal remote top down feature. The unit was removed from my old 2003 Z4 and it worked just fine. All of the connections are the same.
The car: If your car was made 4/04 or later, you will have problems. The car already has an Auto-Top down feature.

1999.5-2001 Audi A4 (B5) HID conversion installation instructions

1. Take the kit out of the box and lay everything out. You can install either the ballasts or bulbs first but typically it is easier to install the bulbs first.
2. There are 3 T27 torx screws holding the headlight on. The 2 on top are visible in this picture.
3. with the 2 screws removed.
4. The third screw is shown here. A long extension is needed to get to it and an extendable magnet is helpful to retrieve the screw (or bit if it falls).
5. Disconnect the headlight and turn signal connectors and remove the headlight by pulling it toward the outside of the car and toward you.

2007-2008 BMW E82/88 135i Intake kit Installation Instructions

Step 1: Complete Stock Intake.
Step 2: Disconnect vacuum line and pull back.
Step 3: Unclip upper half of air box to remove lid and filter.
Step 4: Pull back rubber mount attached to battery cable. Use pliers if necessary. This will allow stock clamp to be loosened. (To be done in step 5B.)
Step 5: A) Loosen clamp closest to the radiator with 1/4” nut driver. B) Loosen clamp closest to fire wall with 1/4” nut driver. Leave clamps in position.