Bumpers Refer to the following illustrations when performing Removal and Installation procedures on the front and rear bumper assemblies. CAUTION: Never apply excessive heat to bumper surface. Heat could cause distortion of the bumper. CAUTION: When collecting exhaust fumes in service area, never attach a metal collector to the exhaust tail pipe because the heat could damage the bumper.
Showing posts with label tail pipe. Show all posts
Showing posts with label tail pipe. Show all posts
Saturday, May 29, 2010
1993 Taurus/Sable Bumpers Removal and Installation
11:04 PM by onesecond
·
0
comments
Labels: 5b, bumpers, excessive heat, exhaust fumes, Ford, front bumper, illustrations, installation procedures, isolator, lb ft, rear bumper, req, rivet, sable, screw, surface heat, tail pipe, taurus
Labels: 5b, bumpers, excessive heat, exhaust fumes, Ford, front bumper, illustrations, installation procedures, isolator, lb ft, rear bumper, req, rivet, sable, screw, surface heat, tail pipe, taurus
Tuesday, May 25, 2010
Chrysler 300C 5.7L Hemi Engine Dynomax Kit 19412 Installation
5:01 AM by onesecond
·
0
comments
Labels: chassis, Chrysler, chrysler 300c, clamps, exhaust system, hangers, installation steps, instruction source, left hand, muffler, PDF Download, rubber isolators, system assembly, tail pipe, tail pipes, turbo mufflers, wd 40
Labels: chassis, Chrysler, chrysler 300c, clamps, exhaust system, hangers, installation steps, instruction source, left hand, muffler, PDF Download, rubber isolators, system assembly, tail pipe, tail pipes, turbo mufflers, wd 40
This dynomax kit for chrysler 300C 5.7L Hemi Engine installation steps:
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂" clamps that connect the mufflers to the x-pipe.
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂" clamps that connect the mufflers to the x-pipe.
Monday, May 17, 2010
1984 Mercedes Benz 190E (201 Chassis) Engine Testing Adjustment
2:36 AM by onesecond
·
0
comments
Labels: air cleaner, automatic climate control, bearing points, check engine oil, coolant, coolant level, dynamometer, dynamometer testing, engine coolant, engine tester, lambda, linkage, measurement sheet, measuring instrument, Mercedes Benz, oil level, tail pipe, test cable, throttle control, throttle valve
Labels: air cleaner, automatic climate control, bearing points, check engine oil, coolant, coolant level, dynamometer, dynamometer testing, engine coolant, engine tester, lambda, linkage, measurement sheet, measuring instrument, Mercedes Benz, oil level, tail pipe, test cable, throttle control, throttle valve
The lambda control and the idle speed emissions level must not be tested when the engine is very hot, e.g. immediately after driving sharply or after measuring engine output on the dynamometer.
Testing, adjusting
1 Complete measurement sheet.
2 Switch off air conditioning or automatic climate control. Move selector lever into position "P".
3 Read out DTC memory. Note: Not available on model year 1984-1986.
Testing, adjusting
1 Complete measurement sheet.
2 Switch off air conditioning or automatic climate control. Move selector lever into position "P".
3 Read out DTC memory. Note: Not available on model year 1984-1986.
Subscribe to:
Posts (Atom)
