2001-2002 Chevrolet Malibu Part Number CV-52-01 Installation

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
Pro.Fit logo and part number will be right side up and readable when installed.

Chevrolet Silverado Rear Vision System Nav Display Installation Instructions

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.

1996-1998 ACURA 3.5 RL w/o GPS Part Number AC-55-96 Instructions

STEP 1. Begin by inserting the hook tool underneath the right rear corner of the black trim bezel that surrounds the shifter lever. Pull upward to release one (1) plastic clip. Perform this same action in the remaining three (3) corners on the bezel, releasing three (3) more plastic clips. Slide the bezel over the shifter knob and disconnect all wiring. Set the bezel aside. Remove the wood grain trim bezel that surrounds the shifter. This bezel also has the ashtray integrated into it. Insert your hook tool underneath the right rear corner of this bezel and pull upward to release right rear clip. Insert the hook tool underneath the left rear cor- ner of the bezel and pull upward to release left rear clip. There are two more clips holding the bezel in place located in front of the shifter just behind the ashtray. Insert your hook tool between the center console padding and the trim bezel on the right side of bezel. Pull upward to release clip. Perform this same action on the left side. Grasp the

1992-96 Toyota Camry Pro.Fit Part Number TY-50-92 Installation Instructions

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Pro.Fit logo and part number will be right side up and readable when installed.
TOOLS REQUIRED: #2 Phillips screwdriver, hook tool.
PARTS INCLUDED: Pro.Fit VSMTM, instructions.
LOCATION: To the right of the radio.

Honda Civic, Acura Integra Gauge Bezel Models 20010 and 20011 Installation

NOTE: Gauge bezel can be painted using a plastic safe paint.
1. Remove stock gauge bezel.
2. Acura Integra - Drill 7⁄64" hole in the plastic cross member. Install aluminum bracket (Fig. 1). Bracket stud should align with hole in lower center of gauge bezel. Honda Civic - Remove bottom center screw from gauge cluster housing. Reinstall screw and supplied aluminum bracket (Fig. 2).

1993-96 Chevrolet Camaro Shaft and DIN Unit Provisions

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from the top of the driver's side knee bolster. Remove (2) 7mm screws from the bottom of the knee bolster. Open the glove box, remove (3) 7mm screws exposed on the right edge of the radio trim bezel and remove the bezel. Remove (2) 7mm screws securing the left side of the factory head unit and (1) 10mm nut securing the right. Slide the unit from the dash and disconnect the wiring. Cut and remove all mounting tabs on the Radio Housing EXCEPT tabs "A". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #5.

1992-95 Cadillac Eldorado & Seville Pro.Vit VSM Installation

STEP 1. Begin by removing the small black trim ring that surrounds the radio. Insert the hook tool behind the upper right corner of the trim ring and pull toward you to loosen the ring. Once the ring is loose, work the remaining three (3) corners of the trim ring loose. Set the trim ring aside. Turn the ignition to the “ON” position and shift the transmission into low gear. Just above the ashtray door, grasp the top section of the bezel that surrounds the transmission shifter and pull toward you to release two (2) clips. Insert the hook tool behind the right rear corner of the bezel just behind the shifter. Pull upward to release one (1) clip. Perform the same action in the left rear corner releasing one (1) more clip. Grasp the rear of the bezel and continue working loose two (2) clips on the left and right sides of the shifter. Work the bezel up and over the shifter knob and disconnect all wiring. Set the bezel aside.

94-96 Cadillac DeVille Universal Taillight Kit Installation

Any part that is modified and/or painted are non returnable.
1. Install steel weld-on light fillers (if applicable)
Measure and trace the housing shape to the area you plan to install them. Cut out the opening of the pattern using a plasma cutter, cutting wheel, or equivalent.
2. Insert the taillight bucket into opening and position as desired. Make sure to place the bucket as level as possible so the light reflects straight back from the vehicle. You can adjust the depth of the taillight bucket based on your preference. Stitch weld the bucket into place.

1992 Chevy Truck G 10 Van V8-305 5.0L Door Trim Panel Service Repair

Remove or Disconnect
Tool Required:
J 9886-01 Door Handle Clip Remover
1. Window regulator handle using J 9886-01.
2. Window regulator handle bezel.
3. Door control assembly handle using J 9886-01.
4. Control assembly handle bezel.
5. Assist strap (if equipped).
6. Arm rest (if equipped).
7. Door trim outer panel screws (if equipped).

Chrysler Pasifica DVD Rear Seat Video System Installation

A – Interior Trim Panel and Component Removal:
1) Disconnect and isolate negative battery cable.
2) Detach the center console shift bezel.
3) Remove ignition key bezel.
4) Remove left and right I/P center bezels using a non-metal trim stick.
5) Disconnect and remove the CD/DVD player or cubby bin (four phillips screws).
6) Disconnect and remove the radio (four phillips screws).