General Motors has decided to conduct a Voluntary Emission Recall involving certain 2001-03 Chevrolet Silverado and GMC Sierra model vehicles, equipped with a 4.3L V6 (RPO L35 - VIN W or RPO LU3 - VIN X) engine. The ignition distributor cap and rotor in these vehicles may corrode and cause ignition system failure. This condition may result in rough engine idle, misfire, stalls, engine cranks but does not run and/or illumination of the Malfunction Indicator Lamp (MIL).
Showing posts with label chevrolet silverado. Show all posts
Showing posts with label chevrolet silverado. Show all posts
Saturday, January 29, 2011
2001-2003 Chevrolet Silverado Ignition Distributor System Corrosion Inspect/Replace
2:59 AM by onesecond
·
0
comments
Labels: Chevrolet, chevrolet silverado, debris source, engine cranks, Ignition, rotor, vent holes, ventilation holes
Labels: Chevrolet, chevrolet silverado, debris source, engine cranks, Ignition, rotor, vent holes, ventilation holes
Wednesday, January 26, 2011
Chevrolet Silverado Rear Backup Camera System
5:48 PM by onesecond
·
0
comments
Labels: Chevrolet, chevrolet silverado, latch handle, mounting bolt, negative battery cable, punch mark, surface, tailgate
Labels: Chevrolet, chevrolet silverado, latch handle, mounting bolt, negative battery cable, punch mark, surface, tailgate
Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure all airbag systems have been disabled for your safety.
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure all airbag systems have been disabled for your safety.
Saturday, January 15, 2011
Putco Chrome Mesh Grille Insert Installation Sheet
12:02 AM by onesecond
·
0
comments
Labels: chevrolet avalanche, chevrolet silverado, gmc sierra, Insert, mesh grille, Other, side vent, Step
Labels: chevrolet avalanche, chevrolet silverado, gmc sierra, Insert, mesh grille, Other, side vent, Step
Grille Pre-installation Preparation
Step 1: Locate the weld-in brackets on the back of the CHROMED MESH GRILLE INSERT(S). These brackets can be found around the aluminum perimeter of the grille insert.
Step 2: Place the Black spring clips found in your installation hardware kit on each of the weld-in brackets located on the
Step 1: Locate the weld-in brackets on the back of the CHROMED MESH GRILLE INSERT(S). These brackets can be found around the aluminum perimeter of the grille insert.
Step 2: Place the Black spring clips found in your installation hardware kit on each of the weld-in brackets located on the
Thursday, December 30, 2010
Chevrolet Silverado Rear Vision System Nav Display Installation Instructions
1:35 AM by onesecond
·
0
comments
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
Subscribe to:
Posts (Atom)
