Camshaft Installation
Step 1: Prepare a clean work area and assemble the tools needed for the camshaft installation. It is suggested to use an automotive manual to help determine which items must be removed from the engine in order to expose the timing chain, lifters and camshaft. A good, complete automotive manual will save time and frustration during the installation.
Showing posts with label Step. Show all posts
Showing posts with label Step. Show all posts
Friday, February 4, 2011
Camshaft Installation and Degreeing Procedure
11:46 PM by onesecond
·
0
comments
Labels: camshaft, camshaft timing, interference fit, Other, proper tool, Step, timing chain
Labels: camshaft, camshaft timing, interference fit, Other, proper tool, Step, timing chain
Vertex Electronic Distributor (2 Wire Unit with Ground)
6:34 PM by onesecond
·
0
comments
Labels: ballast resistor, engine crankshaft, Other, rotor, rotor blade, spark plug wire, spark plug wires, Step
Labels: ballast resistor, engine crankshaft, Other, rotor, rotor blade, spark plug wire, spark plug wires, Step
Old Distributor Removal:
Step 1-Disconnect the coil trigger wire coming from the distributor to the negative (-) side of the ignition coil at the coil terminal. Disconnect the wire supplying current to the positive side (+) of the ignition coil. There may be two wires on this terminal, one from the ballast resistor and one from the starter solenoid. The ballast resistor should have one wire left, the
Step 1-Disconnect the coil trigger wire coming from the distributor to the negative (-) side of the ignition coil at the coil terminal. Disconnect the wire supplying current to the positive side (+) of the ignition coil. There may be two wires on this terminal, one from the ballast resistor and one from the starter solenoid. The ballast resistor should have one wire left, the
Saturday, January 15, 2011
Putco Chrome Mesh Grille Insert Installation Sheet
12:02 AM by onesecond
·
0
comments
Labels: chevrolet avalanche, chevrolet silverado, gmc sierra, Insert, mesh grille, Other, side vent, Step
Labels: chevrolet avalanche, chevrolet silverado, gmc sierra, Insert, mesh grille, Other, side vent, Step
Grille Pre-installation Preparation
Step 1: Locate the weld-in brackets on the back of the CHROMED MESH GRILLE INSERT(S). These brackets can be found around the aluminum perimeter of the grille insert.
Step 2: Place the Black spring clips found in your installation hardware kit on each of the weld-in brackets located on the
Step 1: Locate the weld-in brackets on the back of the CHROMED MESH GRILLE INSERT(S). These brackets can be found around the aluminum perimeter of the grille insert.
Step 2: Place the Black spring clips found in your installation hardware kit on each of the weld-in brackets located on the
Friday, January 14, 2011
Kodiak Installation Instructions
11:58 PM by onesecond
·
0
comments
Labels: angle brackets, bit, bolt hole, cap screws, center punch, PDF Download, Step, ups driver
Labels: angle brackets, bit, bolt hole, cap screws, center punch, PDF Download, Step, ups driver
Part One: Rear bracket attachment
Step 1) Attach the rear brackets to the step as shown in Figure 1, using a washer, E, and nut, I, on each stud. Tighten each nut.
Step 2) Place the cross member in position as shown in Figure 2, and secure using washers D and F, and one nut, H on each stud. Leave fasteners loose, as the bracket slots will be used to determine exact fit of rear upright bracket.
Step 1) Attach the rear brackets to the step as shown in Figure 1, using a washer, E, and nut, I, on each stud. Tighten each nut.
Step 2) Place the cross member in position as shown in Figure 2, and secure using washers D and F, and one nut, H on each stud. Leave fasteners loose, as the bracket slots will be used to determine exact fit of rear upright bracket.
Subscribe to:
Posts (Atom)
