Neo Changer Instruction Manual

Since the Neo Changer will works in many different vehicles the following steps must be taken to ensure the changer is set up correctly for the vehicle it is being installed in.
To prevent damage to your vehicle and the changer take the following precautions.

2005-2008 Ford Mustang Edelbrock Coupe Sub-Frame Connector

Designed to fit 2005-2008 Ford Mustang Coupe, Edelbrock sub-frame connectors are stronger and more effective due to (1) Large welded surface area, (2) connects rear suspension connection point to engine cradle and front K-member, (3) ground clearance is minimally affected.

2001 Chevrolet Impala V6-3.8L Oil Pan Replacement

Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the fuel injector sight shield.
3. Disconnect the intake air temperature (IAT) sensor electrical connector.
4. Remove the air inlet duct from the throttle body.
5. Remove the drive belt.

1998 Chevrolet Truck Lock Cylinder Removal & Installation

Removal Procedures:
1. Remove the steering wheel.
2. Remove the turn signal switch. It is not necessary to completely remove the switch from the column. Pull the switch rearward far enough to slip it over the end of the shaft, but do not pull the harness out of the column.
3. Turn the lock to Run.

Chevrolet Silverado Rear Backup Camera System

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure all airbag systems have been disabled for your safety.

2005 Chevrolet Venture Rocker Panel Replacement

Removal Procedure
Refer to Approved Equipment for Collision Repair Caution in Cautions and Notices.
1. Disable the SIR system. Refer to SIR Disabling and Enabling Zones in SIR.
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical.

Chevrolet Silverado Rear Vision System Nav Display Installation Instructions

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.

2003-07 Dodge Dakota 4.7L PowerAid Throttle Body Spacer

Your PowerAid Throttle Body Spacer was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, please contact AIRAID.
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake hose assembly.
3. Remove throttle body air intake box and save bolts.
4. Remove (3) bolts from the throttle body.

2003 Nissan 350z Driver's Seat Click Noise or Side to Side Movement When Turning

When tuning left or right,
• The driver’s seat makes a “click” noise, and/or
• The driver’s seat moves side to side (left or right),
ACTION:
• Install special washers between the seat thigh support adjuster and the sliding and reclining device—inner and outer (see Figure 1).
NOTE: This is the only authorized repair for this incident (i.e. click noise or side to side movement when turning).
SERVICE PROCEDURE
NOTE: Steps a, b and c below only apply to vehicles equipped with front side (SRS) air bags.
a. Write down all radio station presets.
b. Disconnect the negative battery cable.
c. Wait at least 3 minutes after the negative battery cable is disconnected before removing the driver’s seat.

Neo Car Audio Installation

This chapter provides information required for the installation of the Neo iON, it must be read by all users. Thank you for purchasing the Neo iON. Since the Neo iON works in many different vehicles the following steps must be taken to ensure the iON is set up correctly for the vehicle it is being installed in.
Before Installation
To prevent damage to your vehicle and the iON take the following precautions.
1. Turn off the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the vehicle is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the battery cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution to avoid causing a short circuit during installation. If your radio has a security code make sure you know the code and how to enter it prior to removing the battery cable. The radio will require this code to operate when the battery terminal is reconnected.
2. Do not install the unit in the following locations:
A. Locations exposed to direct sunlight
B. Locations where hot air flows from the cars heater
First Step (For All Vehicles)
The first and most important step in using the Neo iON is setting the dip-switches on the black box; this makes the iON compatible with the vehicle it is being installed in. The iON will not work if this step is not followed correctly. The dip switches can be found on the side of the black plastic box which connects to the iON. Switches are in the “ON” position when they are switched down. Black box settings for each vehicle can be found on the vehicles installation page. Refer to the index to find the page number within this manual that covers your vehicle.

Source

2006 Toyota Highlander Hybrid TVIP V2 (GBS Add On) Installation

1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Be careful not to touch the positive terminal. (b) Remove the air damper wire terminal from the bottom of the glove box. (Fig. 1-2) (1) Remove the clip securing the air damper wire terminal. (c) Remove the glove box. (Fig. 1-3) (1) Remove two stoppers securing the bottom of the glove box. (d) Remove the glove box inner cover. (Fig. 1-4) (1) Remove seven screws securing the cover. (2) Disconnect one connector. (e) Remove the passenger side panel. (Fig. 1-5) (1) Remove two clips securing the cover.

2008 Toyota Highlander EC Rearview Mirror

Steps for EC Rearview Mirror installation: 1. Remove Battery Cable. (a) Protect fender before starting. (b) Do not touch the positive terminal with any tool when removing cable. (c) Remove the negative battery cable. (Fig. 1-1) 2. Vehicle Disassembly. (a) Remove the OE mirror. (1) Disengage the two claws and remove the mirror cover from the mirror base. (Fig. 2-1) (2) Pull the lever in the direction indicated by the arrow shown in the illustration and slide the inner rear view mirror assembly upward to remove it. (Fig. 2-1) (b) Using panel removal tool remove overhead console from headliner. (Fig. 2-2) (1) Disconnect any connectors connected to the overhead console. 3. Install T-taps. (a) Locate the disconnected 22-pin overhead console connector. (Fig. 3-1) (b) Peel back or cut approximately one inch of the wire cover. (Fig. 3-2) (c)

2005-2008 Chrysler 300 2.7L, 3.5L, 5.7L & 6.1L Instructions Sheet

Before removing the factory alternator you must complete the wire check as noted.
Wire Check: The original alternator is externally regulated by the computer. The original plug has two wires, one will have 12.6 volts with the key turned on and the other is the regulation wire. You will have to determine what the wires are conncted to do. This process is as follows: With the vehicle in park and the parking break on, start the vehicle. Using a volt meter, test each of the alternator plug wires. The wire that has the highest voltage is the main power for the voltage regulation. Mark or remember which wire is which for item #5 below.

2002 Mazda MPV LX Key Interlock Inspection

2002 ACCESSORIES & EQUIPMENT' 'Steering Column Switches - MPV
1. Turn the ignition switch to ON position.
2. Shift the selector lever to R position.
3. Verify that the ignition key cannot be turned to LOCK position.
4. Shift the selector lever to P position.
5. Verify that the ignition key can be turned to LOCK position.

1994-1997 Cadillac Seville Revised HVAC Blower Motor Installation Procedures

The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.
The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.
In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.

Chrysler Pasifica DVD Rear Seat Video System Installation

A – Interior Trim Panel and Component Removal:
1) Disconnect and isolate negative battery cable.
2) Detach the center console shift bezel.
3) Remove ignition key bezel.
4) Remove left and right I/P center bezels using a non-metal trim stick.
5) Disconnect and remove the CD/DVD player or cubby bin (four phillips screws).
6) Disconnect and remove the radio (four phillips screws).