Your PowerAid Throttle Body Spacer was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, please contact AIRAID.
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake hose assembly.
3. Remove throttle body air intake box and save bolts.
4. Remove (3) bolts from the throttle body.
Showing posts with label flat head screw. Show all posts
Showing posts with label flat head screw. Show all posts
Thursday, December 2, 2010
2003-07 Dodge Dakota 4.7L PowerAid Throttle Body Spacer
1:51 PM by onesecond
·
0
comments
Labels: air intake hose, bolts, cables, cruise, Dodge, dodge dakota, flat head screw, hose assembly, negative battery cable, power plate, poweraid throttle body spacer, reinforcement ring, retainers, spacers, step 2, throttle body spacer, throttle cable, throttle lever, throttle linkage
Labels: air intake hose, bolts, cables, cruise, Dodge, dodge dakota, flat head screw, hose assembly, negative battery cable, power plate, poweraid throttle body spacer, reinforcement ring, retainers, spacers, step 2, throttle body spacer, throttle cable, throttle lever, throttle linkage
Sunday, June 20, 2010
2005-Present Pontiac G6 Figure Grille Set Installation Instructions
2:21 AM by onesecond
·
0
comments
Labels: bolts, chrome molding, duration, exercise patience, fastener, fasteners, flat head screw, grilles, playing card, Pontiac, pontiac g6, quality materials, radiator, satisfaction, screw driver, tabs
Labels: bolts, chrome molding, duration, exercise patience, fastener, fasteners, flat head screw, grilles, playing card, Pontiac, pontiac g6, quality materials, radiator, satisfaction, screw driver, tabs
These grilles are fabricated employing quality materials and finishes, and have been engineered to enhance the look of your vehicle for the duration of its life. Proper installation is essential to your overall satisfaction, so please read these instructions before attempting to install the grilles. Exercise patience; these instructions are intended to assist even the most mechanically challenged.
Thursday, June 10, 2010
2005-Up Pontiac G6 Figure Grille Set Installation Manual
6:42 AM by onesecond
·
0
comments
Labels: bolts, chrome molding, duration, exercise patience, fastener, fasteners, flat head screw, grilles, playing card, Pontiac, pontiac g6, quality materials, radiator, retainers, satisfaction, screw driver, tabs, vehicle location
Labels: bolts, chrome molding, duration, exercise patience, fastener, fasteners, flat head screw, grilles, playing card, Pontiac, pontiac g6, quality materials, radiator, retainers, satisfaction, screw driver, tabs, vehicle location
These grilles are fabricated employing quality materials and finishes, and have been engineered to enhance the look of your vehicle for the duration of its life. Proper installation is essential to your overall satisfaction, so please read these instructions before attempting to install the grilles. Exercise patience; these instructions are intended to assist even the most mechanically challenged.
Monday, May 31, 2010
Cadillac Escalade & EXT/ESV Liquid Grille 94215 Harley-Davidson Road King Instalation
3:54 AM by onesecond
·
0
comments
Labels: abrasive surface, bolts, brackets, Cadillac, cadillac emblem, cadillac escalade, cadillac escalade ext, escalade ext, flat head screw, harley davidson, harley davidson road king, holes, kit contents, PDF Download, plastic plugs, radiator, radiator cover, screw driver
Labels: abrasive surface, bolts, brackets, Cadillac, cadillac emblem, cadillac escalade, cadillac escalade ext, escalade ext, flat head screw, harley davidson, harley davidson road king, holes, kit contents, PDF Download, plastic plugs, radiator, radiator cover, screw driver
A. Pre-installation Preparation
1. Verify kit contents.
2. Remove protective wrapping from inserts and place on a non-abrasive surface.
3. Remove the brackets and hardware from the box.
1. Verify kit contents.
2. Remove protective wrapping from inserts and place on a non-abrasive surface.
3. Remove the brackets and hardware from the box.
Sunday, May 30, 2010
2005-2008 Chrysler 300 2.7L, 3.5L, 5.7L & 6.1L Instructions Sheet
6:03 AM by onesecond
·
0
comments
Labels: 2008 chrysler 300, 6mm, allen wrench, bolts, Chrysler, chrysler 300, flat head screw, meter test, mounting brackets, negative battery cable, PDF Download, plug wires, step 1, stock, volt meter, voltage regulation, volts
Labels: 2008 chrysler 300, 6mm, allen wrench, bolts, Chrysler, chrysler 300, flat head screw, meter test, mounting brackets, negative battery cable, PDF Download, plug wires, step 1, stock, volt meter, voltage regulation, volts
Before removing the factory alternator you must complete the wire check as noted.
Wire Check: The original alternator is externally regulated by the computer. The original plug has two wires, one will have 12.6 volts with the key turned on and the other is the regulation wire. You will have to determine what the wires are conncted to do. This process is as follows: With the vehicle in park and the parking break on, start the vehicle. Using a volt meter, test each of the alternator plug wires. The wire that has the highest voltage is the main power for the voltage regulation. Mark or remember which wire is which for item #5 below.
Wire Check: The original alternator is externally regulated by the computer. The original plug has two wires, one will have 12.6 volts with the key turned on and the other is the regulation wire. You will have to determine what the wires are conncted to do. This process is as follows: With the vehicle in park and the parking break on, start the vehicle. Using a volt meter, test each of the alternator plug wires. The wire that has the highest voltage is the main power for the voltage regulation. Mark or remember which wire is which for item #5 below.
Saturday, March 27, 2010
Red Snub Mount Installation
1:54 AM by onesecond
·
0
comments
Labels: allen head screws, aluminum engine, Audi, bolts and nuts, flat head screw, foam rubber, frequency vibrations, grease, low frequency, PDF Download, polyurethane, quarter turn, ramps, screw driver, silicon, snub, soapy water, splash shield
Labels: allen head screws, aluminum engine, Audi, bolts and nuts, flat head screw, foam rubber, frequency vibrations, grease, low frequency, PDF Download, polyurethane, quarter turn, ramps, screw driver, silicon, snub, soapy water, splash shield
1. Allow engine to cool before beginning installation.
2. Access the underside of the vehicle.
- APR recommends utilizing a lift for this installation.
- A jack with jack stands or ramps can be used if a lift is not available.
3. Remove the Splash Shield. With the flat head screw driver, unfasten all of the quarter turn screws. Note how splash shield is oriented in the car before removing.
4. Remove the three 6mm bolts from the front lower engine mount.
2. Access the underside of the vehicle.
- APR recommends utilizing a lift for this installation.
- A jack with jack stands or ramps can be used if a lift is not available.
3. Remove the Splash Shield. With the flat head screw driver, unfasten all of the quarter turn screws. Note how splash shield is oriented in the car before removing.
4. Remove the three 6mm bolts from the front lower engine mount.
Subscribe to:
Posts (Atom)
