05-06 Chevrolet C6 Corvette Aft-cat System Installation Instructions

Installation instructions:
1.) Raise and support vehicle.
2.) Lubricate factory hangers/clamps retaining stock system with penetrating oil.
3.) Using a 10mm wrench, remove fasteners retaining rear factory hangers to vehicle frame.

Mitsubishi Lancer Short Throw Shifter Installation Manual

Follow the steps below for installation the short throw shifter on your Mitsubishi Lancer
1. Carefully unscrew the stock shift knob.
2. Remove ashtray and screw beneath it.
3. Remove two screws from inside the center console storage compartment.
4. Lift up on the rear section of the center console and unclip it from the front section.
5. Remove plastic screw from the driver’s side of the center console (near the gas pedal). Remove the plastic cover and the pop rivet beneath it. Then remove the two screws at the rear of the console (were hidden by the rearward part of the center console that was removed).

Land Rover Transport Quality Manual

Observe all conditions as detailed in the “Transport Quality Manual” For detail technical requirements on tasks please refer to relevant service issued instructions. Available on request to Technical Services.
Storage vehicles are classed as all units held in a compound in excess of 2 weeks from compound receipt. Vehicles may require storage for varying periods before the customer takes delivery. It is essential that new products are stored correctly, in order to ensure customer satisfaction and prevent product deterioration. All personnel involved in storage operations must conform to the standards, as detailed here.

2004-05 Chevy Colorado Prerunner Rear Bumper Installation

This kit should only be installed on a vehicle that is in good mechanical condition. Before installing the kit, replace worn or corroded parts. If the vehicle is suspected to have been in a collision or abused, DO NOT install the kit. The components in this kit do not eliminate weaknesses that may exist in the original equipment components.

2004-2005 Cadillac CTS-V JET Performance Products Installation

INSTALLATION INSTRUCTIONS OVERVIEW
Your vehicle has an onboard computer that controls the engine and transmission. The JET programmer reprograms your factory computer according to your specifications with JET Performance Products Tuning.

To reprogram your vehicle’s computer, simply plug the programmer cable into the vehicle’s diagnostic connector, located under the dash panel on the driver’s side. Set the parking brake. Next, turn the ignition key to RUN but do not start the engine. It will then identify your vehicle and ask a series of questions on its LCD screen. When completed, turn the key to OFF and disconnect the cable from the diagnostic connector. Now you’re “Engineered for Power”.

2005-2008 Chrysler 300 2.7L, 3.5L, 5.7L & 6.1L Instructions Sheet

Before removing the factory alternator you must complete the wire check as noted.
Wire Check: The original alternator is externally regulated by the computer. The original plug has two wires, one will have 12.6 volts with the key turned on and the other is the regulation wire. You will have to determine what the wires are conncted to do. This process is as follows: With the vehicle in park and the parking break on, start the vehicle. Using a volt meter, test each of the alternator plug wires. The wire that has the highest voltage is the main power for the voltage regulation. Mark or remember which wire is which for item #5 below.

07-Up Chevy Tahoe LED Upper Quarter Panel Light

Your new IPCW LED Upper Quarter Panel Lights are quality-made products that will work beautifully on your vehicle. Please refer to the pictures below for installation instructions.
Remove the screws in Figure A with a Phillips screwdriver. Untwist the sockets, then gently slide out the tail light.
After the tail light is removed. remove the screw in Figure B.
Remove the screw in Figure C to remove the Upper Quarter panel.
Gently slide out the stock Upper Quarter Panel.

GMC/Chevy 2500HD/3500 Installation Instructions

This kit is designed only for use on GMC/Chevy 2001-present 8-lug vehicles.
1. Inspect the kits to make sure that all parts and fasteners were provided. The parts list (for each portal)
2. Block or otherwise retain the vehicle from moving. Remove the current steering components from the GMC vehicle. If necessary, take measurements to determine the current toe-in. (An alignment is still necessary.)
3. Remove the old steering assembly from the vehicle. Remove the outer tie rod ends, pitman arm, idler arm, and frame mount for the idler arm.

Chrysler Magnum, Charger, 300C, SRT-8 Anti-roll Bar Set Installation

1) Secure the rear wheels with blocks and jack the front up. Support the front of the vehicle with jack stands on the frame. Observe the stock sway bar orientation and position for reference.
Note: If you are using a 4 post lift or alignment rack, you do not have to jack the front up.
2) Remove the heat shields that cover the subframe mounts using a 10mm wrench or socket.
3) Remove the subframe mounts by unbolting 2 bolts per mount using a 15mm socket. The Sway bar should be hanging by it’s endlinks at this point. Retain all hardware and brackets for reinstallation.