2005-06 HONDA CRV Grill/ Brush Guard Part #6049

Procedure installing the Grill to Honda CRV
1. Remove the plastic rivets securing the plastic guard located underneath the vehicle in order to install the front bar.
2. Start with the passenger side assembly, postion one of the 7/16 nut plates behind the cross member opening and align the 7/16 nut plate wit the two matching holes in the frame rail. Fasten the frame brackets to the bottom cross member as shown in the illustration using the 7/16 x 1 ¼ hex bolts, 7/16 washers, 5/16 self tapping bolt and 5/16 washers. Note: Do not over tighten 5/16 x 1 self tapping bolt as it might strip threads.

07 Honda CR-V Grille Guard Installation Instructions

Installation procedure the grille guard on Honda CR-V
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY.
2. Using a flat screwdriver carefully remove all fasteners from factory plastic shroud on top and underneath the vehicle. On the bottom there are (4) on the front and (3) on each side by the fender. On the top there are (7) fasteners.
3. Remove bottom plastic shroud and place it on a working area. Using a hack saw carefully cut the marked area shown in Figure 1.

2005-Present Pontiac G6 Figure Grille Set Installation Instructions

These grilles are fabricated employing quality materials and finishes, and have been engineered to enhance the look of your vehicle for the duration of its life. Proper installation is essential to your overall satisfaction, so please read these instructions before attempting to install the grilles. Exercise patience; these instructions are intended to assist even the most mechanically challenged.

2002-05 Cadillac Escalade Front Bar Part # 4049 Installation Instructions

Installing the mounting frame brackets
1. Remove factory tow hooks from front section of vehicle
2. Align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below.
3. Attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: 2WD models, you may have to cut a space in the plastic spoiler for the bottom of the front bar up rights to slide through and eventually attach to the frame mounting brackets.

2005-Up Pontiac G6 Figure Grille Set Installation Manual

These grilles are fabricated employing quality materials and finishes, and have been engineered to enhance the look of your vehicle for the duration of its life. Proper installation is essential to your overall satisfaction, so please read these instructions before attempting to install the grilles. Exercise patience; these instructions are intended to assist even the most mechanically challenged.

2005-2006 Cadillac STS Exhaust System Installation

Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of materials provided on the previous page to assure that you have all the parts necessary for the installation of your new Borla Performance Cat-Back ™ Exhaust System.

2002 Cadillac Escalade Front Bar Part #4049 A Installation Instructions

INSTALLING THE MOUTNING FRAME BRACKETS
1. Remove factory tow hooks from front section of vehicle
2. align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below. See figure 1.1
3. attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: (2WD MODELS YOU MAY HAVE TO CUT A SPACE IN THE PLASTIC SPOILER FOR THE BOTTOM OF THE FRONT BAR UP RIGHTS TO SLIDE THROUGH AND EVENTUALLLY ATTACH TO THE FRAME MOUNTING BRACKETS.

Automatic Retracting Running Board Installation Instructions

Drill Holes for Rear Arm
Locate the Drill Template in the parts kit. Place it along the sill 1/16" in front of the rear sill drain. Use vise grips to secure the Template to the sill. Drill a 1/8" pilot hole at each location in the Template. Remove the Template and drill the holes out to 21/64".

Drill Holes for Front Arm
Most Vehicles
Clamp the Drill Template to the pinch weld 1/8" behind the front mounting tab. Drill a 1/8" pilot hole at each location in the Template. Remove the Template and drill the holes out to 21/64". SUV's – Driver’s Side Only Clamp the Drill Template 1/8" in front of the sill drain. Then drill the holes as above.

GMC/Chevy 2500HD/3500 Installation Instructions

This kit is designed only for use on GMC/Chevy 2001-present 8-lug vehicles.
1. Inspect the kits to make sure that all parts and fasteners were provided. The parts list (for each portal)
2. Block or otherwise retain the vehicle from moving. Remove the current steering components from the GMC vehicle. If necessary, take measurements to determine the current toe-in. (An alignment is still necessary.)
3. Remove the old steering assembly from the vehicle. Remove the outer tie rod ends, pitman arm, idler arm, and frame mount for the idler arm.

2001 GMC Truck C 1500 Truck 2WD Front Side Door Window Regulator Motor Replacement

Removal Procedure
1. Raise the window. If the window motor is inoperable, remove the window to gain access to the window motor retaining screws. Refer to Front Side Door Window Replacement.
2. Remove the power window module.
3. With the window regulator on the bench, remove fasteners one (1) and two (2) which will disconnect the drive housing and motor (4) from the rail (5) motor slides out of the gear/spool, hold the gear/spool into the housing with your fingers. The spool will unwind if it comes out of the housing.
4. Holding the motor and housing together, remove fastener three (3).
5. Slide the motor partially out of the gear/spool allowing finger access to the gear spool (6). Hold the gear/spool into the housing and remove the motor (7).

GRIP Chevy Cobalt Body Kit Installation

All GRIP body kits need to be properly sanded and primed before painting, even if the part arrives pre-primed. Failure to properly prepare parts before painting can result in poor paint finish and adhesion. Please prefit parts before painting! Once a part has been painted or modified in any way it cannot be returned.
1: Look over vehicle before installing the body kit to make note of all attachment points on existing fascia. Since GRIP uses all existing attachment points, it is very important not to harm existing mounting holes and / or fasteners. Some fasteners that are drilled out cannot be reused. It is very important to use special care when removing the reusable fasteners from the panels since they will not be provided by GRIP. GRIP only provides non-reusable fasteners with its kits.