Installation note:
• Be careful not to damage the body paint finish.
• This interior trim kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
1. Using isopropyl alchohol on a shop towel, clean the area where the right outlet trim will attach.
2. Peel back one inch from the end of the 13 adhesive backings shown, and attach them to the front of the right outlet panel with masking tape. Remove and discard the three remaining adhesive backings from the trim.
Showing posts with label honda cr v. Show all posts
Showing posts with label honda cr v. Show all posts
Monday, November 15, 2010
2008 Honda CR-V Interior Panel Set P/N 08Z03-SWA-100A Installation
12:04 AM by onesecond
·
0
comments
Labels: alchohol, alcohol, ambient air temperature, body paint, Honda, honda cr v, interior panel, masking tape, palm of your hand, shop towel, swa
Labels: alchohol, alcohol, ambient air temperature, body paint, Honda, honda cr v, interior panel, masking tape, palm of your hand, shop towel, swa
Sunday, November 14, 2010
Honda CR-V DVD Navigation Attachment
1:52 AM by onesecond
·
0
comments
Labels: airbag, clamps, curtain, har, Honda, honda cr v, model 1, navigation unit, pillar, pins, precaution, sunvisor, tabs, torx screws, wire harness, wire ties
Labels: airbag, clamps, curtain, har, Honda, honda cr v, model 1, navigation unit, pillar, pins, precaution, sunvisor, tabs, torx screws, wire harness, wire ties
DVD AVN Navigation Unit P/N: 08A40-1J6-100
Wire Harness Routing Precaution
Disconnect the connectors and terminals by holding them. Do not pull the harness to disconnect the connector.
Do not pull the harness with force. it will damage the har ness.
Cut off the excess of the wire ties.
Connect the connectors and terminals securely until they lock.
Reinstall the connectors to the corresponding stays whenever they are removed. After operation, check that the connectors are installed on the stays securely and not loose or come out of the stays.
Wire Harness Routing Precaution
Disconnect the connectors and terminals by holding them. Do not pull the harness to disconnect the connector.
Do not pull the harness with force. it will damage the har ness.
Cut off the excess of the wire ties.
Connect the connectors and terminals securely until they lock.
Reinstall the connectors to the corresponding stays whenever they are removed. After operation, check that the connectors are installed on the stays securely and not loose or come out of the stays.
Tuesday, November 9, 2010
2005 Honda CR-V Door Visors P/N 08R04-S9A-101
3:47 AM by onesecond
·
1 comments
Labels: 2005 honda cr v, alcohol, ambient air temperature, brackets, glass run, Honda, honda cr v, masking tape, mirror base, paint, palm of your hand, rear end, sash, shock, shop towel
Labels: 2005 honda cr v, alcohol, ambient air temperature, brackets, glass run, Honda, honda cr v, masking tape, mirror base, paint, palm of your hand, rear end, sash, shock, shop towel
Installation Door Visors on Honda CR-V 2005:
NOTE: • These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors.
• Be careful not to damage the paint finish or glass run channels when installing the door visors.
• Handle the door visors with care. They are not designed to absorb shock or impact.
• This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours.
NOTE: • These instructions show the left door visors being installed. The same procedure applies to installing of the right door visors.
• Be careful not to damage the paint finish or glass run channels when installing the door visors.
• Handle the door visors with care. They are not designed to absorb shock or impact.
• This door visor kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours.
2002-04 Honda CR-V BX2232 Baseplate Installation
3:43 AM by onesecond
·
0
comments
Labels: 10mm socket, auto manufacturer, baseplate, blue ox baseplates, bolt, end plates, fascia, hardware kit, holes, Honda, honda cr v, metric bolts, minor adjustments, push pins, pushpins, rangefinder, tabs, tolerances, tow bar, variations
Labels: 10mm socket, auto manufacturer, baseplate, blue ox baseplates, bolt, end plates, fascia, hardware kit, holes, Honda, honda cr v, metric bolts, minor adjustments, push pins, pushpins, rangefinder, tabs, tolerances, tow bar, variations
Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Many Blue Ox® Baseplates are designed to use existing holes and hardware to mount the baseplate to the towed vehicle. Even though bolts are there, do not assume they are adequate for baseplate mounting. Always use hardware supplied in the hardware kit and existing hardware specified in the Baseplate Installation Instructions.
Many Blue Ox® Baseplates are designed to use existing holes and hardware to mount the baseplate to the towed vehicle. Even though bolts are there, do not assume they are adequate for baseplate mounting. Always use hardware supplied in the hardware kit and existing hardware specified in the Baseplate Installation Instructions.
07 Honda CR-V Grille Guard Installation Instructions
3:32 AM by onesecond
·
0
comments
Labels: factory bumper, fasteners, fender, flat screwdriver, flat washer, flat washers, grille guard, hack, head bolt, hex head, holes, Honda, honda cr v, mounting bracket, mounting brackets, radiator, radiator support, rear hole, shell, shroud
Labels: factory bumper, fasteners, fender, flat screwdriver, flat washer, flat washers, grille guard, hack, head bolt, hex head, holes, Honda, honda cr v, mounting bracket, mounting brackets, radiator, radiator support, rear hole, shell, shroud
Installation procedure the grille guard on Honda CR-V
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY.
2. Using a flat screwdriver carefully remove all fasteners from factory plastic shroud on top and underneath the vehicle. On the bottom there are (4) on the front and (3) on each side by the fender. On the top there are (7) fasteners.
3. Remove bottom plastic shroud and place it on a working area. Using a hack saw carefully cut the marked area shown in Figure 1.
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY.
2. Using a flat screwdriver carefully remove all fasteners from factory plastic shroud on top and underneath the vehicle. On the bottom there are (4) on the front and (3) on each side by the fender. On the top there are (7) fasteners.
3. Remove bottom plastic shroud and place it on a working area. Using a hack saw carefully cut the marked area shown in Figure 1.
2002-2006 Honda CR-V Subwoofer Kit Installation Instructions
3:30 AM by onesecond
·
0
comments
Labels: antenna, bolts, careful care, dashboard, flat tip, fuse box, glove box, hazard switch, Honda, honda cr v, negative cable, pins, radio station, retaining clips, seat cd changer, self tapping screw, self tapping screws, subwoofer, tabs
Labels: antenna, bolts, careful care, dashboard, flat tip, fuse box, glove box, hazard switch, Honda, honda cr v, negative cable, pins, radio station, retaining clips, seat cd changer, self tapping screw, self tapping screws, subwoofer, tabs
The subwoofer can not be installed with an under-seat CD changer.
Installation the Subwoofer to 2002-2006 CRV:
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Remove the two screws that fasten the bottom of the center panel.
4. Pull the center panel out toward you to release the six clips, unplug the vehicle connector from the hazard switch, and remove the center panel. Be careful care not to damage the clips.
Installation the Subwoofer to 2002-2006 CRV:
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Remove the two screws that fasten the bottom of the center panel.
4. Pull the center panel out toward you to release the six clips, unplug the vehicle connector from the hazard switch, and remove the center panel. Be careful care not to damage the clips.
Monday, May 31, 2010
2006 Honda CR-V Rear Differential Fluid Inspection and Replacement
3:19 AM by onesecond
·
0
comments
Labels: 4wd system, differential, differential fluid, dirt, drain plug, filler plug, Honda, honda cr v, level c, oil filler, solvent
Labels: 4wd system, differential, differential fluid, dirt, drain plug, filler plug, Honda, honda cr v, level c, oil filler, solvent
This pdf will guide you to inspect and replace the real differential for honda cr-v. 1. With the vehicle on level ground, inspect the differential fluid with the ignition switch turned to LOCK (0). 2. Use solvent and a brush to wash off any oil and dirt from the differential fluid inspection oil filler plug. 3. Remove the oil filler plug (A) and the sealing washer (B), then check the condition of the fluid, and make sure the fluid is at the proper level (C). 4. The fluid level must be up to the fill hole. If it is below the hole, add the differential fluid until it runs out, then reinstall the
Thursday, May 20, 2010
02 Honda CR-V Creaking From A-Pillar When Turning Left
4:12 PM by onesecond
·
0
comments
Labels: bolts, cam chain, diagnostic tool, Honda, honda cr v, hook up, jsp, pillar, spot weld, steelman
Labels: bolts, cam chain, diagnostic tool, Honda, honda cr v, hook up, jsp, pillar, spot weld, steelman
If owners of ’02 CR-Vs are complaining of a creaking from the A-pillar when turning left, the problem may be the right front engine mount on the cam chain side. If the rubber in the mount is misadjusted or faulty, it can make a creaking, ticking, or spot-weld-like noise that seems to be coming from the base of the front passenger’s A-pillar.
Subscribe to:
Posts (Atom)
