2006 Chevrolet Express SA315 Speaker Mounting Bracket

Installation: Read all warnings before starting installation.
1. This bracket mounts above the radiator. Remove the front fascia to gain access to the radiator (see manufacturers instructions).

6700 Dodge Viper Heat Shields For 1992-1999 Roadster

RIGHT SIDE: 1. Remove top of heater blower box from lower heater box assembly in engine compartment.
2. Remove the bolts from the coolant reservoir so it can be moved around.
3. Disconnect spark plug wires from spark plugs and move out of the way.
4. Loosen the 2nd and 4th upper header flange bolts for mounting bracket installation.
5. Install one mounting bracket on each of the two header flange bolts loosened in Step 4. Position the brackets so that the slot on the end is straight down under the bolt and bracket is flat on top. These brackets will angle forward and down slightly when installed properly. NOTE: Before attempting to install the heat shield onto the brackets, first measure the distance between the threaded holes in the mounting brackets. You should have 9 1/8” from center to center of holes. If you don’t, you can bend the brackets with a pair of pliers or a small hammer. Doing this will make heat shield installation much easier.

07 Honda CR-V Grille Guard Installation Instructions

Installation procedure the grille guard on Honda CR-V
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY.
2. Using a flat screwdriver carefully remove all fasteners from factory plastic shroud on top and underneath the vehicle. On the bottom there are (4) on the front and (3) on each side by the fender. On the top there are (7) fasteners.
3. Remove bottom plastic shroud and place it on a working area. Using a hack saw carefully cut the marked area shown in Figure 1.

67-72 C-10 Truck Sport Sway Bar Kit 22108 Instructions

Raising Vehicle
Raise front of the vehicle by using a 4 post lift or drive-on ramps. Securely block the rear wheels of the vehicle. Do not remove the front wheels during installation. It is imperative that the vehicle is at ride height for this installation.
Install Frame Mounts
First step is to install the frame mounts. The mounts utilize existing rivet holes in the frame. You will need to air chisel the rivets as shown below. Once the holes are clear, grab the 3/8” x 1.5” hex bolts & washers from the “front” hardware bag and insert them into the rivet holes facing down. Position the mounting bracket to the frame rail and begin fastening the 3/8” bolts with the provided washers and nylock nuts. Do not tighten all the way! Grab the 3/8” x 1.25” hex bolts and drop them into the mount holes on the bracket itself. Don’t forget to use washers. You can now fully tighten the frame bolts at this time.

00-05 Mitsubishi Eclipse Front Kit Part No. 75504

Always keep safety in mind when working on your vehicle. Completely read these instructions before installing the kit.
Preparing the Vehicle
1. Elevate the vehicle and secure the frame with jack stands.
2. Remove the front wheels.
Strut Removal
1. Remove the three nuts securing the upper strut mounting bracket and discard.
NOTE: These are located inside the engine compartment above the strut pocket.

BMW Bluetooth Kit Installation Instructions

The BMW Bluetooth Kit Installation Instructions for BMW 3 Series / M3 Coupe, Sedan, Convertible03/02-MY06 (E46) The installation time for this kit is approximately 1.25 hour These instructions were developed especially for BMW vehicles and are not to be compared to any existing instructions for vehicles other than BMW. No methods other than those specified in this document are to be used to install the BMW Universal BluetoothTM Hands-Free Kit

2002-05 Cadillac Escalade Front Bar Part # 4049 Installation Instructions

Installing the mounting frame brackets
1. Remove factory tow hooks from front section of vehicle
2. Align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below.
3. Attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: 2WD models, you may have to cut a space in the plastic spoiler for the bottom of the front bar up rights to slide through and eventually attach to the frame mounting brackets.

1988-1995 Chevy V8 305 & 350 TBI Airaid Intake System Installation

Remove Factory Intake Assembly
a) Loosen the wing on the top of the factory air intake assembly and remove assembly from vehicle.
b) Remove and discard the 1” crankcase breather ring. See Fig#1 (save valve cover breather tube for later use)
c) Use a 13mm socket and wrench to remove the strap that secures the silencer tube on the passenger side fender housing. See Fig#2
d) Remove entire factory air cleaner assembly from vehicle.

2006 Toyota Highlander Hybrid TVIP V2 (GBS Add On) Installation

1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Be careful not to touch the positive terminal. (b) Remove the air damper wire terminal from the bottom of the glove box. (Fig. 1-2) (1) Remove the clip securing the air damper wire terminal. (c) Remove the glove box. (Fig. 1-3) (1) Remove two stoppers securing the bottom of the glove box. (d) Remove the glove box inner cover. (Fig. 1-4) (1) Remove seven screws securing the cover. (2) Disconnect one connector. (e) Remove the passenger side panel. (Fig. 1-5) (1) Remove two clips securing the cover.

2002 Cadillac Escalade Front Bar Part #4049 A Installation Instructions

INSTALLING THE MOUTNING FRAME BRACKETS
1. Remove factory tow hooks from front section of vehicle
2. align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below. See figure 1.1
3. attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: (2WD MODELS YOU MAY HAVE TO CUT A SPACE IN THE PLASTIC SPOILER FOR THE BOTTOM OF THE FRONT BAR UP RIGHTS TO SLIDE THROUGH AND EVENTUALLLY ATTACH TO THE FRAME MOUNTING BRACKETS.

1989-1996 Dodge Dakota Trucks Ignition Coil Tests

The ignition coil for the vehicles covered by this guide is in the following locations:
• 1989-92 engines: mounted to the firewall
• 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor
• 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head
• 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket.

3 3/4" Tachometer Engine Cylinder Adjustments Installation

This tachometer is factory calibrated for 8 cylinder engines. For operation on 4 or 6 cylinder engines, a switch adjustment must be made.
1. Remove cup by placing the tachometer face down on a smooth surface. Remove the phillips screw on the back and gently lift the cup off to expose the circuit board. Take care
not to pull on the wires.
2. Locate the switch on the circuit board. Move each of the two switches to the proper cylinder selection according to the diagram illustration on the right.
4 Cyl.- Both switches down
6 Cyl.- Switch #1 down. Switch #2 up
8 Cyl.- Both switches up
3.Replace the case on the tach with mounting bracket at the bottom (make sure the wires are clear of the screw hole).
4. Replace the screw

1958-64 Chevy Rear End Kit Installation Instructions

INSTALLING THE FORWARD 4-LINK MOUNTING BRACKET:
1. The stock‘58-64 Chevy forward control-arm brackets will need to be trimmed to accept the new fabricat- ed forward 4-link control-arm brackets in your kit.
2. Looking at the front of the factory control- arm bracket, you’ll need to remove the material as shown. Keep the outside edge of the bracket (pen pointing to this edge) vertically straight. The new bracket seats against this edge on both sides of chassis.
3. Install the new bracket all the way into the stock frame bracket pocket until it seats on the outer edge. Keep the new bracket to the top edge of pocket