Inner-Edge Interior Lightbar Installation Guide

Installation:
Note: When routing the wires, it is important to choose a path that will keep the wires away from excessive heat or any vehicle equipment that could compromise the integrity of the wires (ex. trunk lids, door jams, etc.)

2003-Up Nissan 350Z Edelbrock Nitrous System

The Edelbrock Nissan 350Z Performer EFI Nitrous System (Part Number 71007) is designed for 2003-Later Nissan 350Z vehicles equipped with stock 3.5L engines that utilize the returnless style fuel system. Horsepower and torque increases can vary with equipment upgrades and modifications.

3300 SuperGlide Installation Instructions

This guide provides several pages of instructions for the installation of the SuperGlide towing system (part number 3300).
Truck Preparation
1. Check part quantities using the Parts List for the specific vehicle type.
2. Block vehicle wheels. Some vehicles may require you to raise the rear of the truck in order to make it easier to drill for installing the Mounting Brackets on the truck frame.
3. You may wish to remove the wheels, to give yourself greater working room.

07 Honda CR-V Grille Guard Installation Instructions

Installation procedure the grille guard on Honda CR-V
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY.
2. Using a flat screwdriver carefully remove all fasteners from factory plastic shroud on top and underneath the vehicle. On the bottom there are (4) on the front and (3) on each side by the fender. On the top there are (7) fasteners.
3. Remove bottom plastic shroud and place it on a working area. Using a hack saw carefully cut the marked area shown in Figure 1.

98-01 Toyota Corolla Sport Sway Bar Set Installation

INSTALLATION OF HOTCHKIS FRONT SWAY BAR
1.) Please look at the original front antiroll bar and note the orientation of the front bar. You will want to install the new Hotchkis bar in the same manner.
2.) Use a 14mm wrench and 6mm Allen wrench to remove the nuts holding the end links to the ends of the stock sway bar. Remove the end links from the ends of the sway bar. Retain the hard ware for later use.
3.) Remove the cross piece from the sway bar mount on each side using a 19mm wrench or socket.
4.) Using a 12mm socket or wrench remove one the three mounting brackets.

2002-05 Cadillac Escalade Front Bar Part # 4049 Installation Instructions

Installing the mounting frame brackets
1. Remove factory tow hooks from front section of vehicle
2. Align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below.
3. Attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: 2WD models, you may have to cut a space in the plastic spoiler for the bottom of the front bar up rights to slide through and eventually attach to the frame mounting brackets.

2002 Cadillac Escalade Front Bar Part #4049 A Installation Instructions

INSTALLING THE MOUTNING FRAME BRACKETS
1. Remove factory tow hooks from front section of vehicle
2. align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below. See figure 1.1
3. attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: (2WD MODELS YOU MAY HAVE TO CUT A SPACE IN THE PLASTIC SPOILER FOR THE BOTTOM OF THE FRONT BAR UP RIGHTS TO SLIDE THROUGH AND EVENTUALLLY ATTACH TO THE FRAME MOUNTING BRACKETS.

2005-2008 Chrysler 300 2.7L, 3.5L, 5.7L & 6.1L Instructions Sheet

Before removing the factory alternator you must complete the wire check as noted.
Wire Check: The original alternator is externally regulated by the computer. The original plug has two wires, one will have 12.6 volts with the key turned on and the other is the regulation wire. You will have to determine what the wires are conncted to do. This process is as follows: With the vehicle in park and the parking break on, start the vehicle. Using a volt meter, test each of the alternator plug wires. The wire that has the highest voltage is the main power for the voltage regulation. Mark or remember which wire is which for item #5 below.

2007-2008 Chevy SuperRail Mounting Kit #4423 Installation

Truck Preparation
1. Check part quantities using the Parts List on Page 2.
2. Block vehicle wheels. Some vehicles may require you to raise the rear of the truck in order to make it easier to drill for installing the mounting brackets on the truck frame.
3. You may wish to remove the wheels, to give yourself greater working room.
4. If you have purchased a template, proceed to “Template Method” below; otherwise, begin with the “Layout Method.”