The OEM and PnP Plugs have release tabs that must be pressed before rotating the locking levers. Failure to use the release tabs may result in plug damage. Connect and disconnect the PnP connectors several times to get a feel for how the plugs work. When rotating the OEM and PnP Plug locking levers, if the Plug is fully seated in the connector the locking mechanism will be correctly engaged and the plug will be drawn down into the connector. If the Plug is not fully seated, the locking mechanism will not be fully seated and although the locking lever rotates and feels like it locks, the locking mechanism will not be engaged and the plug will vibrate loose resulting in illumination of multiple dash lights.
Showing posts with label toyota corolla. Show all posts
Showing posts with label toyota corolla. Show all posts
Tuesday, August 10, 2010
Toyota Corolla, MY09-10, 1.8L Unichip PnP Installation Instructions
7:19 PM by onesecond
·
0
comments
Labels: corolla, dash lights, dirt, ecu, engine compartment, failure, fuse box, illumination, levers, locking lever, negative terminal, oem, plastic connector, plastic strip, release tabs, several times, Toyota, toyota corolla, velcro strip, wiring loom
Labels: corolla, dash lights, dirt, ecu, engine compartment, failure, fuse box, illumination, levers, locking lever, negative terminal, oem, plastic connector, plastic strip, release tabs, several times, Toyota, toyota corolla, velcro strip, wiring loom
98-01 Toyota Corolla Sport Sway Bar Set Installation
3:22 AM by onesecond
·
0
comments
Labels: 12mm socket, allen wrench, bolts, bushings, corolla, cross brace, front sway bar, gas tank, grease, hotchkis tuning, mounting brackets, mounting plates, nuts, orientation, professional note, socket 4, stock hardware, Toyota, toyota corolla, toyota corolla sport
Labels: 12mm socket, allen wrench, bolts, bushings, corolla, cross brace, front sway bar, gas tank, grease, hotchkis tuning, mounting brackets, mounting plates, nuts, orientation, professional note, socket 4, stock hardware, Toyota, toyota corolla, toyota corolla sport
INSTALLATION OF HOTCHKIS FRONT SWAY BAR
1.) Please look at the original front antiroll bar and note the orientation of the front bar. You will want to install the new Hotchkis bar in the same manner.
2.) Use a 14mm wrench and 6mm Allen wrench to remove the nuts holding the end links to the ends of the stock sway bar. Remove the end links from the ends of the sway bar. Retain the hard ware for later use.
3.) Remove the cross piece from the sway bar mount on each side using a 19mm wrench or socket.
4.) Using a 12mm socket or wrench remove one the three mounting brackets.
1.) Please look at the original front antiroll bar and note the orientation of the front bar. You will want to install the new Hotchkis bar in the same manner.
2.) Use a 14mm wrench and 6mm Allen wrench to remove the nuts holding the end links to the ends of the stock sway bar. Remove the end links from the ends of the sway bar. Retain the hard ware for later use.
3.) Remove the cross piece from the sway bar mount on each side using a 19mm wrench or socket.
4.) Using a 12mm socket or wrench remove one the three mounting brackets.
Thursday, May 27, 2010
2005–2007 Toyota Corolla R & R Engine Control Module
6:41 PM by onesecond
·
0
comments
Labels: 2007 toyota corolla, automatic transaxle, automatic transmission, corolla, diagnostic procedures, drivetrain, engine control module, engine control module ecm, improvements, information system, powertrain, powertrain control, solenoid, solenoid valve, technical information, tis, Toyota, toyota corolla, transaxle, transaxle system
Labels: 2007 toyota corolla, automatic transaxle, automatic transmission, corolla, diagnostic procedures, drivetrain, engine control module, engine control module ecm, improvements, information system, powertrain, powertrain control, solenoid, solenoid valve, technical information, tis, Toyota, toyota corolla, transaxle, transaxle system
Some 2005 – 2007 model year Corolla and Matrix vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and a M.I.L. “ON” with DTC P2716 stored. Improvements have been made to the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) to reduce the possibility of this condition occurring. Use the following procedure to repair the vehicle.
2006 Toyota Corolla Engine Control Module Removal and Installation
6:17 PM by onesecond
·
0
comments
Labels: 2006 toyota corolla, corolla, delco, denso, engine control module, glove compartment, negative terminal, screw, screws, Toyota, toyota corolla, wire harness
Labels: 2006 toyota corolla, corolla, delco, denso, engine control module, glove compartment, negative terminal, screw, screws, Toyota, toyota corolla, wire harness
REPLACEMENT 1. DISCONNECT BATTERY NEGATIVE TERMINAL
2. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
a. Remove the screw from the glove compartment door stoppers.
b. Deform the upper part of the glove compartment door assembly to release the stoppers.
c. Pull the glove compartment door assembly upward to remove it.
3. REMOVE ECM
a. Remove the 2 clips using a clip remover, then open the cover.
b. Disconnect the 4 ECM connectors.
2. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
a. Remove the screw from the glove compartment door stoppers.
b. Deform the upper part of the glove compartment door assembly to release the stoppers.
c. Pull the glove compartment door assembly upward to remove it.
3. REMOVE ECM
a. Remove the 2 clips using a clip remover, then open the cover.
b. Disconnect the 4 ECM connectors.
2006 Toyota Corolla Air Conditioning Unit Assy
5:56 PM by onesecond
·
0
comments
Labels: 2006 toyota corolla, air conditioning unit, caution label, clamp, corolla, dirt, illustration, instrument panel, piping, pliers, refrigerant, refrigeration system, release lever, screwdriver, sst, suction hose, Toyota, toyota corolla, tube assembly, water hose
Labels: 2006 toyota corolla, air conditioning unit, caution label, clamp, corolla, dirt, illustration, instrument panel, piping, pliers, refrigerant, refrigeration system, release lever, screwdriver, sst, suction hose, Toyota, toyota corolla, tube assembly, water hose
HINT: Installation is in the reverse order of removal.
1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM SST 07110-58060 (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)
2. DISCONNECT SUCTION HOSE SUB-ASSEMBLY
a. Install SST to piping clamp. SST 09870-00015 HINT: Confirm the direction of the piping clamp claw and SST using the illustration showing on the caution label.
b. Push down SST and release the clamp lock. NOTE: Be careful not to deform the tube, when pushing SST.
c. Pull SST slightly and push the release lever, then remove the piping clamp with SST.
1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM SST 07110-58060 (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)
2. DISCONNECT SUCTION HOSE SUB-ASSEMBLY
a. Install SST to piping clamp. SST 09870-00015 HINT: Confirm the direction of the piping clamp claw and SST using the illustration showing on the caution label.
b. Push down SST and release the clamp lock. NOTE: Be careful not to deform the tube, when pushing SST.
c. Pull SST slightly and push the release lever, then remove the piping clamp with SST.
Subscribe to:
Posts (Atom)
