Procedure installing the Grill to Honda CRV
1. Remove the plastic rivets securing the plastic guard located underneath the vehicle in order to install the front bar.
2. Start with the passenger side assembly, postion one of the 7/16 nut plates behind the cross member opening and align the 7/16 nut plate wit the two matching holes in the frame rail. Fasten the frame brackets to the bottom cross member as shown in the illustration using the 7/16 x 1 ¼ hex bolts, 7/16 washers, 5/16 self tapping bolt and 5/16 washers. Note: Do not over tighten 5/16 x 1 self tapping bolt as it might strip threads.
Showing posts with label inner edge. Show all posts
Showing posts with label inner edge. Show all posts
Sunday, November 14, 2010
2005-06 HONDA CRV Grill/ Brush Guard Part #6049
1:39 AM by onesecond
·
0
comments
Labels: bolt, brackets, brush guard, cross member, fasteners, frame rail, hex bolts, hex nuts, holes, Honda, honda crv, illustration, inner edge, screw, screws, slots, support bracket, tapping, utility knife, wit
Labels: bolt, brackets, brush guard, cross member, fasteners, frame rail, hex bolts, hex nuts, holes, Honda, honda crv, illustration, inner edge, screw, screws, slots, support bracket, tapping, utility knife, wit
Saturday, June 19, 2010
2002-05 Cadillac Escalade Front Bar Part # 4049 Installation Instructions
11:40 PM by onesecond
·
0
comments
Labels: Cadillac, cadillac escalade, factory tow, fasteners, hex bolts, hex nuts, holes, inner edge, models, mounting bracket, mounting brackets, outer edge, PDF Download, spoiler, tow hooks
Labels: Cadillac, cadillac escalade, factory tow, fasteners, hex bolts, hex nuts, holes, inner edge, models, mounting bracket, mounting brackets, outer edge, PDF Download, spoiler, tow hooks
Installing the mounting frame brackets
1. Remove factory tow hooks from front section of vehicle
2. Align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below.
3. Attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: 2WD models, you may have to cut a space in the plastic spoiler for the bottom of the front bar up rights to slide through and eventually attach to the frame mounting brackets.
1. Remove factory tow hooks from front section of vehicle
2. Align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below.
3. Attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: 2WD models, you may have to cut a space in the plastic spoiler for the bottom of the front bar up rights to slide through and eventually attach to the frame mounting brackets.
Tuesday, June 1, 2010
2002 Cadillac Escalade Front Bar Part #4049 A Installation Instructions
9:37 PM by onesecond
·
0
comments
Labels: 2002 cadillac escalade, Cadillac, cadillac escalade, factory tow, fasteners, hex bolts, hex nuts, holes, inner edge, models, mounting bracket, mounting brackets, outer edge, PDF Download, spoiler, tow hooks
Labels: 2002 cadillac escalade, Cadillac, cadillac escalade, factory tow, fasteners, hex bolts, hex nuts, holes, inner edge, models, mounting bracket, mounting brackets, outer edge, PDF Download, spoiler, tow hooks
INSTALLING THE MOUTNING FRAME BRACKETS
1. Remove factory tow hooks from front section of vehicle
2. align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below. See figure 1.1
3. attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: (2WD MODELS YOU MAY HAVE TO CUT A SPACE IN THE PLASTIC SPOILER FOR THE BOTTOM OF THE FRONT BAR UP RIGHTS TO SLIDE THROUGH AND EVENTUALLLY ATTACH TO THE FRAME MOUNTING BRACKETS.
1. Remove factory tow hooks from front section of vehicle
2. align driver side mounting bracket to the bottom and outer edge existing holes. Position bracket in manner shown below. See figure 1.1
3. attach mounting frame brackets using the 7/16 x 1 ― hex bolts, 7/16 hex nuts and 7/16 washers. (hand tighten as you may have to move the brackets around slightly, to align the front bar)
NOTE: (2WD MODELS YOU MAY HAVE TO CUT A SPACE IN THE PLASTIC SPOILER FOR THE BOTTOM OF THE FRONT BAR UP RIGHTS TO SLIDE THROUGH AND EVENTUALLLY ATTACH TO THE FRAME MOUNTING BRACKETS.
Subscribe to:
Posts (Atom)
