Always keep safety in mind when working on your vehicle. Completely read these instructions before installing the kit.
Preparing the Vehicle
1. Elevate the vehicle and secure the frame with jack stands.
2. Remove the front wheels.
Strut Removal
1. Remove the three nuts securing the upper strut mounting bracket and discard.
NOTE: These are located inside the engine compartment above the strut pocket.
Showing posts with label loctite. Show all posts
Showing posts with label loctite. Show all posts
Sunday, September 19, 2010
00-05 Mitsubishi Eclipse Front Kit Part No. 75504
9:51 PM by onesecond
·
0
comments
Labels: 7a, bearing, bolts, engine compartment, flat washers, holes, loctite, Mitsubishi, mitsubishi eclipse, mounting bracket, nuts, rubber bushing, rubber side, shaft, strut assembly, sway bar link, thread sealant, wheels
Labels: 7a, bearing, bolts, engine compartment, flat washers, holes, loctite, Mitsubishi, mitsubishi eclipse, mounting bracket, nuts, rubber bushing, rubber side, shaft, strut assembly, sway bar link, thread sealant, wheels
Sunday, June 20, 2010
Vauxhall Cavalier 4x4 Transfer box Temperature Sensor, Removal & Installation & Oil Level Checking
1:49 AM by onesecond
·
0
comments
Labels: 1d, 4x4, bulkhead, caution, copper, detachable collar, drip tray, dud, fig 2d, loctite, new sensor, nylon ties, oil level, oil spillage, opel, pipe work, temperature sensor, threads, tie bar, vauxhall cavalier
Labels: 1d, 4x4, bulkhead, caution, copper, detachable collar, drip tray, dud, fig 2d, loctite, new sensor, nylon ties, oil level, oil spillage, opel, pipe work, temperature sensor, threads, tie bar, vauxhall cavalier
Warning: The 4x4 transfer box (txb) temperature sensor is fragile and easily damaged. There is absolutely no reason to remove the temperature sensor unless it is being replaced. Removing the Temperature Sensor
701. With the txb cold, trace the cabling back from the txb sensor (Fig.2D) to its connector at the bulkhead (Fig.A & B).
702. Disconnect the sensor, remove the detachable plastic part of the connector (txb side - Fig.1D) and carefully withdraw the cabling back to the underneath of the vehicle - (Facilitates threading through the ring spanner)
701. With the txb cold, trace the cabling back from the txb sensor (Fig.2D) to its connector at the bulkhead (Fig.A & B).
702. Disconnect the sensor, remove the detachable plastic part of the connector (txb side - Fig.1D) and carefully withdraw the cabling back to the underneath of the vehicle - (Facilitates threading through the ring spanner)
Friday, March 5, 2010
2003 BMW K1200 GT, LT, RS Steering Damper Mounting Kit Installation Instructions
5:12 PM by onesecond
·
0
comments
Labels: BMW, bmw k1200 gt, bolt, clamp, degreaser, friction, g tank, good tools, hyperpro, loctite, lt, max 2, mistake, motorcycle, oil film, PDF Download, self adhesives, steering damper, surfaces, time untill
Labels: BMW, bmw k1200 gt, bolt, clamp, degreaser, friction, g tank, good tools, hyperpro, loctite, lt, max 2, mistake, motorcycle, oil film, PDF Download, self adhesives, steering damper, surfaces, time untill
Before Installation:
- Please read the entire manual carefully before starting the installation!
- Check if you have all the tools required. Good tools are a must.
- Protect your bike at the most important places in and around the work area (e.g. tank, fairing, frame, etc.), with a blanket, towel or similar.
During Installation:
- Check all operations and parts carefully before, during and after performing each step.
- Clean all surfaces that are required for fitting parts together or for applying self adhesives or loctite, thoroughly with contactcleaner or another degreaser, unless otherwise stated.
- Be carefull not to damage or scratch any part of your bike.
- ALWAYS work relaxed and concentrated!! It is very easy to damage something or make a mistake.
- Please read the entire manual carefully before starting the installation!
- Check if you have all the tools required. Good tools are a must.
- Protect your bike at the most important places in and around the work area (e.g. tank, fairing, frame, etc.), with a blanket, towel or similar.
During Installation:
- Check all operations and parts carefully before, during and after performing each step.
- Clean all surfaces that are required for fitting parts together or for applying self adhesives or loctite, thoroughly with contactcleaner or another degreaser, unless otherwise stated.
- Be carefull not to damage or scratch any part of your bike.
- ALWAYS work relaxed and concentrated!! It is very easy to damage something or make a mistake.
Subscribe to:
Posts (Atom)
