06 Chevrolet Aveo/Wave Cruise Control Installation Instructions

INSTALLATION
1) Remove knee panel under steering column, then remove (6) 10mm screws to release steel panel.
2) Remove lower steering column cover and driver side kick panel.
3) Connect the Red Cruise Harness Wire to Pink 12v Ignition Vehicle Wire behind fuse.
4) Connect the Black Cruise Harness Wire to Black Wire/Position 87 of 4

2003-2005 Honda Pilot Vehicle Wiring

WIRING INFORMATION: 2003 Honda Pilot WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness ACCESSORY WIRE YELLOW Ignition Harness SECOND ACCESSORY WIRE WHITE/BLACK Ignition Harness POWER DOOR LOCK (-) BLUE/GREEN Large Green Harness At Passenger Fuse POWER DOOR UNLOCK (-) BLACK/RED Box Test door lock wires while turning the key in the passenger door. PARKING LIGHTS (+) RED/BLACK Plug At Driver Fuse Box DOOR

2008 Toyota Highlander EC Rearview Mirror

Steps for EC Rearview Mirror installation: 1. Remove Battery Cable. (a) Protect fender before starting. (b) Do not touch the positive terminal with any tool when removing cable. (c) Remove the negative battery cable. (Fig. 1-1) 2. Vehicle Disassembly. (a) Remove the OE mirror. (1) Disengage the two claws and remove the mirror cover from the mirror base. (Fig. 2-1) (2) Pull the lever in the direction indicated by the arrow shown in the illustration and slide the inner rear view mirror assembly upward to remove it. (Fig. 2-1) (b) Using panel removal tool remove overhead console from headliner. (Fig. 2-2) (1) Disconnect any connectors connected to the overhead console. 3. Install T-taps. (a) Locate the disconnected 22-pin overhead console connector. (Fig. 3-1) (b) Peel back or cut approximately one inch of the wire cover. (Fig. 3-2) (c)

2001 Honda Accord EX Ignition Checks

2001 ENGINE PERFORMANCE' 'Basic Diagnostic Procedures Ignition Coil Test (Accord 2.3L & CR-V)
1. Turn ignition off. Remove distributor cap, rotor and leak cover. Remove primary leads from ignition coil. Using an ohmmeter, check primary resistance between ignition coil terminals "A+" and "B-". See Fig. 12 . Resistance should be as specified. See IGNITION COIL RESISTANCE table. 2. Check secondary resistance between ignition coil terminal "A+" and secondary output terminal (ignition coil tower). See IGNITION COIL RESISTANCE table. If readings are not as specified, replace ignition coil.

Jetta Wiring diagram Instrument Cluster

Below the information found at the wiring diagram:
Information for ♦ Relay and Fuse arrangements ♦ Connector arrangements ♦ Control Modules and Relays ♦ Ground Connections Component Locations Information for ♦ Troubleshooting Procedures -Guided Fault Finding using VAS 5051/5052 Power Supply Relay (terminal 30, B+), Vehicle Electrical System Control Module, Power Supply Relay 2 (terminal 15) A ‐ Battery C ‐ Generator (GEN) J317 ‐ Power Supply Relay

2005+ Chrysler Vehicles Auxiliary Audio Input Installation

Installation:
The CHYX plugs into the back of the factory radio.
1. Remove factory radio. Remove factory female 10 pin Satellite cable, if available. Plug the CHYX’s 10 pin SAT plug into the radio. Plug the factory Satellite cable that was just removed into into the CHYX’s 10 pin connector.
2. Insert the CHYX’s 22 pin main power Plug (T-Harness) in between the factory radio and factory harness.
3. Connect external audio devices(s) into Aux 1 and/or Aux 2 inputs using the RCA jacks on the CHYX.

DICE ipod BMW Z4 Installation

This “how to” guide installs the kit into a Z4 with no CD changer and a standard business cd (no sat nav), ipod location in the central compartment.
1: The kit
2: Disconnect battery with 10mm socket
3: Now it’s a bit of a pain, but to get easier access to centre console I removed the boot carpet. Use a large flat head screwdriver to remove the retaining screws on the left and the right hand side of the boot. You need to reach behind the carpet to hold the nut at the back.