Pacific Western Design 53/54 Chevrolet Wiper System is designed to install in cars which are modified to use a 12- volt negative ground electrical system only and is not available for 6-volt(original)cars.
Showing posts with label wiper motor. Show all posts
Showing posts with label wiper motor. Show all posts
Monday, January 3, 2011
1953/54 Chevrolet RainGear Wiper System Installation Instructions
3:20 AM by onesecond
·
0
comments
Labels: 54 chevrolet, ashtray, Chevrolet, control cable, electrical system, electrical wiring, glove box, hex nuts, original cars, pivot shafts, radio speaker, radio support, raingear, spool assembly, stock radio, studs, support bracket, vacuum motor, wiper arms, wiper motor
Labels: 54 chevrolet, ashtray, Chevrolet, control cable, electrical system, electrical wiring, glove box, hex nuts, original cars, pivot shafts, radio speaker, radio support, raingear, spool assembly, stock radio, studs, support bracket, vacuum motor, wiper arms, wiper motor
Sunday, May 30, 2010
2003 Subaru Outback Wiper & Washer Systems
11:58 PM by onesecond
·
0
comments
Labels: arrow, blade, bolts, figure source, general description, legacy outback, motor assembly, Subaru, subaru outback, tightening torque, torque, washer systems, wiper motor
Labels: arrow, blade, bolts, figure source, general description, legacy outback, motor assembly, Subaru, subaru outback, tightening torque, torque, washer systems, wiper motor
2003 ACCESSORIES & EQUIPMENT Wiper & Washer Systems - Baja, Legacy & Outback REAR WIPER ARM
Removal 1. Raise wiper arm cover (A). 2. Loosen nut to remove wiper arm.
INSTALLATION 1. Install in the reverse order of removal. 2. Operate rear wiper once. 3. Align blade to rear defogger heat wire (A).
Tightening torque: Refer to FRONT WIPER , COMPONENT, General Description.
Removal 1. Raise wiper arm cover (A). 2. Loosen nut to remove wiper arm.
INSTALLATION 1. Install in the reverse order of removal. 2. Operate rear wiper once. 3. Align blade to rear defogger heat wire (A).
Tightening torque: Refer to FRONT WIPER , COMPONENT, General Description.
Tuesday, May 18, 2010
Jetta Wiring diagram Instrument Cluster
10:59 PM by onesecond
·
0
comments
Labels: a2, battery c, c generator, component locations, control modules, electrical system, fuse holder, fuse panel, ground connections, instrument cluster, instrument panel, jetta, pin connector, power supply, sa1, sc2, troubleshooting procedures, Volkswagen, wiper motor, wiring harness
Labels: a2, battery c, c generator, component locations, control modules, electrical system, fuse holder, fuse panel, ground connections, instrument cluster, instrument panel, jetta, pin connector, power supply, sa1, sc2, troubleshooting procedures, Volkswagen, wiper motor, wiring harness
Below the information found at the wiring diagram:
Information for ♦ Relay and Fuse arrangements ♦ Connector arrangements ♦ Control Modules and Relays ♦ Ground Connections Component Locations Information for ♦ Troubleshooting Procedures -Guided Fault Finding using VAS 5051/5052 Power Supply Relay (terminal 30, B+), Vehicle Electrical System Control Module, Power Supply Relay 2 (terminal 15) A ‐ Battery C ‐ Generator (GEN) J317 ‐ Power Supply Relay
Information for ♦ Relay and Fuse arrangements ♦ Connector arrangements ♦ Control Modules and Relays ♦ Ground Connections Component Locations Information for ♦ Troubleshooting Procedures -Guided Fault Finding using VAS 5051/5052 Power Supply Relay (terminal 30, B+), Vehicle Electrical System Control Module, Power Supply Relay 2 (terminal 15) A ‐ Battery C ‐ Generator (GEN) J317 ‐ Power Supply Relay
Subscribe to:
Posts (Atom)
