Subaru Fuel Injector Removal Procedures

When removing and/or replacing the fuel injector(s), it’s imperative that the below instructions be strictly followed. Failing to do so may result in damage to the injector(s).
Applicability: All Legacy, Impreza and SVX models.
Note: Pliers or any other tools not specified in these instructions should not be used under any circumstances to prevent damage to the fuel injector(s).

2004+ Subaru Impreza WRX/STI Front Lip (polyurethane)

Polyurethane is a flexible material. Occasionally during shipping, sections of the lip may warp or bend in unusual shapes. DO NOT WORRY! Simply lay the lip flat and out in the sun for a day and it will return to its normal shape. To cure the waviness of the front portion, simply purchase a long metal or wood section, clamp this metal section inside the lip (clamps can be purchased at Home Depot), and lay out in the sun for about a day. This will fix the waviness problem.

2001-2004 Subaru Outback Skid Plate Installation Instructions

REMOVAL OF ORIGINAL SPLASH PAN Raise and safely support the vehicle on jack stands or on ramps. Locate and remove the two 12mm bolts at the rear of the factory splash pan. Locate and remove the two 10mm screws from the left and right side of the factory splash pan. These are located up inside the fender. Locate and remove the three remaining 12mm bolts from the front of the factory splash pan. The splash pan has retaining tabs around the three bolt holes from the last step and will require some downward force to remove the splash pan from the vehicle

Subaru Impreza ABS System Problem Technical Bulletin

This technical bulletin deals with common problems encountered on various manufacturers’ vehicles by the helpline staff over the last few months. These faults have been re -occurring during this time, and the following topics detail the faults and where possible the solutions to the problems.
Fault: ABS warning light constantly “ON” with no ABS operation. Callers often remark that they are unable to communicate with the ABS ECM even though using suitable diagnostic equipment.

1997 Subaru Legacy GT Sedan Timing Belt Service and Repair

1997 Subaru Legacy GT Sedan AWD F4-2.5L DOHC Vehicle Level Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Installation INSTALLATION SPROCKET 1) Install right-hand belt cover No.2. 2) Install left-hand belt cover No.2. 3) Install tensioner bracket 4) Install crankshaft sprocket. 5) Install right-hand exhaust camshaft sprocket. To lock camshaft, use ST. 6) Install right-hand intake camshaft sprocket using ST. 7) Install left-hand exhaust camshaft sprocket using ST. 8) Install left-hand intake camshaft sprocket using ST.

2003 Subaru Outback Wiper & Washer Systems

2003 ACCESSORIES & EQUIPMENT Wiper & Washer Systems - Baja, Legacy & Outback REAR WIPER ARM
Removal 1. Raise wiper arm cover (A). 2. Loosen nut to remove wiper arm.
INSTALLATION 1. Install in the reverse order of removal. 2. Operate rear wiper once. 3. Align blade to rear defogger heat wire (A).
Tightening torque: Refer to FRONT WIPER , COMPONENT, General Description.

1998 Subaru Legacy L Sedan Lighting and Horns Parking Lamp Electric Diagram

1998 Subaru Legacy L Sedan AWD F4-2.2L SOHC Vehicle Level Diagrams Electrical Diagrams Lighting and Horns Parking Lamp
Fuse/Relay Locations: For fuse and/or relay locations refer to Starting and Charging / Power and Ground Distribution: See: Power and Ground Distribution Ground Locations: For ground locations refer to Vehicle / Locations / Harness: See: Locations\Grounds Connector Locations: For connector locations refer to Vehicle / Locations / Connectors: See: Locations\Connectors Component Locations: For component locations refer to Vehicle / Locations / Harness: See: Locations\Harness