All Nissan models using Vent Control Valve P/Ns 14935-AM60A / AM60B
SERVICE INFORMATION
When replacing the EVAP canister vent control valve for any reason: Use the one listed in the PARTS INFORMATION section of this bulletin on Page 2. For vent control valve replacement procedure, refer to the appropriate section of the Electronic Service Manual (ESM) if needed.
Showing posts with label o ring. Show all posts
Showing posts with label o ring. Show all posts
Wednesday, December 22, 2010
Nissan Vent Control Valve Replacement Service Bulletin
12:53 AM by onesecond
·
0
comments
Labels: control valve, electronic service, esm, frontier, information section, information service, new style, Nissan, nissan models, o ring, tie straps, valve replacement, vent
Labels: control valve, electronic service, esm, frontier, information section, information service, new style, Nissan, nissan models, o ring, tie straps, valve replacement, vent
Monday, November 22, 2010
Subaru Fuel Injector Removal Procedures
1:53 AM by onesecond
·
0
comments
Labels: air cleaner, air flow meter, applicability, correct position, engine oil, fingers, flat screwdriver, fuel injector, fuel pump, fuel rail, imperative, impreza, inch blade, o ring, pliers, power steering hose, rubber spacer, Subaru, svx, upper case
Labels: air cleaner, air flow meter, applicability, correct position, engine oil, fingers, flat screwdriver, fuel injector, fuel pump, fuel rail, imperative, impreza, inch blade, o ring, pliers, power steering hose, rubber spacer, Subaru, svx, upper case
When removing and/or replacing the fuel injector(s), it’s imperative that the below instructions be strictly followed. Failing to do so may result in damage to the injector(s).
Applicability: All Legacy, Impreza and SVX models.
Note: Pliers or any other tools not specified in these instructions should not be used under any circumstances to prevent damage to the fuel injector(s).
Applicability: All Legacy, Impreza and SVX models.
Note: Pliers or any other tools not specified in these instructions should not be used under any circumstances to prevent damage to the fuel injector(s).
Saturday, June 12, 2010
1996 Chevy Blazer FT-100D & ATAS-100 Installation
5:34 AM by onesecond
·
0
comments
Labels: 28 july, atas 100, Chevrolet, chevy blazer, diamond antenna, ft 100d, garages, o ring, PDF Download, pl, radio, special thanks, teflon, two feet, wedge plate
Labels: 28 july, atas 100, Chevrolet, chevy blazer, diamond antenna, ft 100d, garages, o ring, PDF Download, pl, radio, special thanks, teflon, two feet, wedge plate
Installation works fine. Power lead (fused) was run from the battery using #10 stranded wire. Ground wire was bonded to the body about two feet from the radio. Ground quality was measured to be excellent. Each vehicle should be checked nevertheless. Mount is the Diamond Antenna #400C, which has the SO-239 base and 6.5’ RG316 Teflon Coax with a PL-259
Monday, June 7, 2010
1955-64 Chevy Rear Axle Bearing Installation
5:24 AM by onesecond
·
0
comments
Labels: axle bearings, axles, brake drums, brake shoes, Chevrolet, chevy rear axle, chisel, hammer, lip seal, nuts, o ring, PDF Download, rear end, rear wheels, retainer, retaining ring, seals, soft material, studs, style ball
Labels: axle bearings, axles, brake drums, brake shoes, Chevrolet, chevy rear axle, chisel, hammer, lip seal, nuts, o ring, PDF Download, rear end, rear wheels, retainer, retaining ring, seals, soft material, studs, style ball
The rear axle bearings that are used on a 1955 to 1964 are a “press- on” style ball bearing. The bearing supports the axle in the rear end housing and also serves as the seal and axle retainer. An O-ring around the outside of the bearing seals to the rear end housing, while a lip seal is located on the outside face of the bearing that keeps rear end lube inside the housing. When an axle bearing starts to leak (usually because the bearing cage is disintegrating) the rear end lube will ruin the rear brake shoes. If the bearing becomes loose, it will start to roar and possibly ruin the axle and/or rear end housing. In this article we will show the proper way to remove and install new rear axle bearings.
Subscribe to:
Posts (Atom)
