Neo Car Audio Installation

This chapter provides information required for the installation of the Neo iON, it must be read by all users. Thank you for purchasing the Neo iON. Since the Neo iON works in many different vehicles the following steps must be taken to ensure the iON is set up correctly for the vehicle it is being installed in.
Before Installation
To prevent damage to your vehicle and the iON take the following precautions.
1. Turn off the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the vehicle is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the battery cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution to avoid causing a short circuit during installation. If your radio has a security code make sure you know the code and how to enter it prior to removing the battery cable. The radio will require this code to operate when the battery terminal is reconnected.
2. Do not install the unit in the following locations:
A. Locations exposed to direct sunlight
B. Locations where hot air flows from the cars heater
First Step (For All Vehicles)
The first and most important step in using the Neo iON is setting the dip-switches on the black box; this makes the iON compatible with the vehicle it is being installed in. The iON will not work if this step is not followed correctly. The dip switches can be found on the side of the black plastic box which connects to the iON. Switches are in the “ON” position when they are switched down. Black box settings for each vehicle can be found on the vehicles installation page. Refer to the index to find the page number within this manual that covers your vehicle.

Source

Application and Installation Instruction for GM12LAN-AUX/S

The GM12LAN-AUX/S converts the XM satellite radio port of the GM radio into an auxiliary input. The GM12LAN-AUX/S provides full compatibility with the factory On-Star system, and factory XM Satellite Radio. Additional harness is required. (Not included).

DO NOT force connectors together as pin damage may occur. This installation will be flawless if you take your time making the connections described below. Following the installation sequence below is critical to ensure proper recognition of the auxiliary interface by the factory radio.

2006-2008 Honda Pilot Dash Disassembly

1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Using a small flat blade screw- driver remove the blank plate from upper right side of radio trim panel. (Figure A) 3 Unsnap radio trim panel. Unplug switches and remove panel. (Figure B) 4 Remove (4) 10mm bolts securing radio, unplug and remove radio.

2004-2006 Chevy Colorado Brute Force Intake System Installation

Getting Started
a) Make sure vehicle is parked on a level surface. Set parking brake.
b) Disconnect negative battery terminal from the battery.
c) If engine has run within the past two hours, let it cool down.
Removal of the stock intake system.
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process.

1993-96 Chevrolet Camaro Shaft and DIN Unit Provisions

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from the top of the driver's side knee bolster. Remove (2) 7mm screws from the bottom of the knee bolster. Open the glove box, remove (3) 7mm screws exposed on the right edge of the radio trim bezel and remove the bezel. Remove (2) 7mm screws securing the left side of the factory head unit and (1) 10mm nut securing the right. Slide the unit from the dash and disconnect the wiring. Cut and remove all mounting tabs on the Radio Housing EXCEPT tabs "A". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #5.

Audi TT V-Flow Intake Install Instructions

Start with your Phillips head screw driver and remove the three screws on top of your battery cover. Then remove the battery cover from the car.
Firmly grasp the plug on top of your MAF sensor unplugging it. Lay the plug back away from the intake system.
Using your Phillips head screwdriver loosen the hose clamp next to the MAF housing.
You will notice a hose with a 90 degree bend and a small plastic ring around the end of it snapped into place at the bottom of the factory air box. Firmly squeeze the top and the bottom of that ring squeezing together and pull the hose off of the factory air box. Pull the hose back and tuck it back out of the work space.