MaxiEST EST201 Tool Manual

Location of Data Link Connector (DLC)
The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic brake tools interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle’s service manual for the location.

BMW Universal Bluetooth Hands-Free System (ULF) Owner's Manual

Universal BluetoothTM Hands-Free System (ULF)
The BMW Universal Bluetooth Hands-Free System (ULF) utilizes Bluetooth wireless technology to enable a wireless connection to be established between a Bluetooth enabled mobile phone and the ULF Control Module installed in the vehicle. The combination of these components results in a new generation of in-vehicle phone system. The ULF Control Module forms an interface that allows a mobile phone with the embedded BluetoothTM wireless technology feature to be wirelessly integrated into the vehicle. For the first time BMW is introducing a new generation hands-free telephone system kit that provides the customer with the option of using various BluetoothTM enabled mobile phones (a list of recommended phones is available from your BMW Center).

Application and Installation Instruction for GM12LAN-AUX/S

The GM12LAN-AUX/S converts the XM satellite radio port of the GM radio into an auxiliary input. The GM12LAN-AUX/S provides full compatibility with the factory On-Star system, and factory XM Satellite Radio. Additional harness is required. (Not included).

DO NOT force connectors together as pin damage may occur. This installation will be flawless if you take your time making the connections described below. Following the installation sequence below is critical to ensure proper recognition of the auxiliary interface by the factory radio.

Toy01 Installation Instructions

The Toy01 is an interface that was developed for 2003 and later Toyota and Lexus which will enable a direct audio video input to the vehicle navigation screen / audio system. Vehicles that have the color screens but no navigation the Toy01 will enable you to add an aftermarket navigation system. To install the Toy01 the installer must have access to the rear of the screen and control unit.

GMRC-03 Cadillac Class II Data Bust Interface Installation Instructions

The GMRC-03 is designed to be used in Cadillac’s that do not have Onstar or amplified systems. It will retain the warning chimes that are lost when the factory radio is removed. The GMRC-03 will also provide a 12 volt switched accessory wire for proper radio operation. *Note: The GMRC-03 can be used in Cadillac’s that come with a factory amplifier; however the factory amplifier must be bypassed and the speaker wires on the GMRC-03 must not be used. Running new wires to the speakers is recommended. If the Cadillac also has Onstar, that feature will be lost.

Cadillac CTS Installation Modification

The Cadillac CTS left channel audio is wired differently than all other vehicles compatible with the SIR-GM1. The left channel audio and ground wires are switched which can cause phasing and noise problems. To correct this, a simple modification must be made to the factory SDAR interface harness included with the SIR-GM1.

Audi A4L Installation Manual

This interface offers RGB, AV inserting onto A4/A5/Q5 panel in a plug-n-play way without cutting wire or using solders. It also offers these functions:
● super Stable,Clear and high-resolution RGB processing for Navigation map display.
● automatic camera switch.
● Optional adjustable reverse guideline display for helping reversing.
● Speed pulse, Reverse, Night lamp signals decoded from the CAN bus for the aftermarket navigation.

Installation location：
Remove the big plastic part shown by the yellow arrow，[No screws, only hooks]， then the total plastic can be taken down, and then the 4 screws can be seen.
Remove the 4 screws, then the panel can be taken down, the interface can be installed behind it.
There is a 10P cable which is carrying the signals, the interface will be inserted onto this cable.

6Pin connector to the Box：
Yellow：Battery 12V，BLACK：GND，
RED：ACC（can generated），
GREEN：REVERSE，
WHITE ： Switch signal[=5V when MODE pressed]。
GREY：Please do not use

source

Audi Gateway 500 with Dual FOT Installation

Installation of GATEWAY 500 unit Dual FOT
For All Audi vehicles: A good location to mount the GATEWAY 500 unit is at the CD Changer behind the glove box. If the vehicle is equipped with the in-dash CD Changer, install the GATEWAY 500 unit behind it. Interfacing in the MOST optical ring should be done as shown in the installation guide.
For All Audi vehicles NOT equipped with a factory CD Changer, the GATEWAY 500 interface shall be integrated into the optical MOST ring at the output of the head unit.
For All Audi vehicles equipped with a factory CD Changer, the GATEWAY 500 interface shall be installed at the factory CD Changer location

Audi RVC Interface Installation Instructions

Installation requires special knowledge.
Do not install the unit yourself. For safe and reliable installation, consult a dealer having special knowledge.
• Never use bolts or nuts from the car’s safety devices for installation. If bolts or nuts from the steering wheel, brakes or other safety devices are used for installation of the unit, it may cause an accident.
• Use the unit with a DC 12V negative ground car. This unit cannot be used in large trucks which use a DC 24V battery. If it is used with a DC 24V battery, it may cause a fire or accident.

Audi To Most System VT-AUDIMOSTCK3100-100 Parrot CK3100 BlueTooth

This Interface has been designed to be installed together with the Parrot CK3100 Hands-free kit (NOT SUPPLIED WITH THE INTERFACE). It will not be necessary to use the Display supplied with the CK3100 kit, because the Interface allows to view all information about calls in the Audi OEM MMI Monitor.The Parrot BLUE Module and the suitable wiring will be needed to complete the installation.

Audi TT 8J Roadster A3 Cabriolet Convertible Top interface Installation Guide

Convertible top interface
• Convenient interior (one-Touch) operation - Control with the remote - Fully automated opening and closing.
• Usage of original connectors.
• Operate while driving up to the pace of 60 km/h (50 km/h to 60 km/h).
• Indication of opening and closing convertible top by flashing indicators (optional).

Audi MMI‐3G Interface Installation Manual

This interface can insert video/RGB onto MMI 3G screens, so reverse image, AV, TV tuner video can be displayed. It has the following features:
Plug and play installation without hurting the original circuit.
1 RGB+2AV+1 camera video input.
Optional headrest can be installed.

The 6P power connector definition:
DIP Settings
1．Yellow：Constant power 12V。
2．BLACK：Ground to Chassis
3．GREEN：reverse video trigger wire[=12V when reverse]