MaxiEST EST201 Tool Manual

Location of Data Link Connector (DLC)
The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic brake tools interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle’s service manual for the location.

Acura RSX Heated Mirror Installation Instructions

Heated Mirrors: I have installed heated mirrors in the US model. Here's what I did; but before installing make sure you read through the entire instructions so you have a good idea what is expected.
Tools: Here are some of the tools you will need. If you don’t have most of these or know how to use them, STOP. This is not for you.
Disclaimer: These instructions are for reference only. Anyone who uses these instructions agrees to hold the author harmless. It is the users’ responsibility to verify the suitability of these reference instructions to their vehicle.

Manual Service Reset Volvo 240 (1986 - 1989)

Reach behind the instrument panel and push the lever located between the tachometer and the speedometer. Volvo 240 (1990 - 1993) 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. 2. Insert a thin-bladed tool into the cavity and press the reset button.
Volvo 850 (1993 - 1995) fitted with the Yazaki instrument panel
NOTE: This instrument panel has the odometer located above the speedometer needle. OM1033 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. 2. Insert a thin-bladed tool into the cavity and press the reset button.
Volvo 850 (1993 - 1995) fitted with the VDO instrument panel
NOTE: This instrument panel has the odometer located below the speedometer needle. 1. With the ignition switch in the ON position and the engine not running. Diagnostic module located in engine compartment adjacent to LH suspension mount 2. Connect the diagnostic module test lead to terminal 7. 3. Press the reset button on the diagnostic module 4 times in quick succession. 4. When the LED on the diagnostic unit illuminates and stays illuminated, press the reset button once and release it. 5. When the LED illuminates and stays illuminated, press the button 5 times in quick succession. 6. When the LED illuminates again, press the button once. 7. The LED will flash several times to indicate that the sequence has been correctly entered and the SRI has been reset. 8. Unplug the test lead from terminal 7 and turn the ignition switch to the ‘OFF’ position.

Source

Electronic Parking Brake Service Tool Instructions

Location of the Data Link Connector (DLC)
The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where the service tool interfaces with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle’s service manual for the location.

Onstar GMOS06 Installation Instructions

INSTALLING THE GMOS-06
1)With all connections completed to the aftermarket radio, plug the 32 pin harness into the Cadillac’s wiring harness.
*Note: some minor modifications may be necessary to the sub dash cavity to accommodate the GMOS-06.
2) Cycle the key by turning the ignition on then back off, then on again to test the radio.

GMRC-03 Cadillac Class II Data Bust Interface Installation Instructions

The GMRC-03 is designed to be used in Cadillac’s that do not have Onstar or amplified systems. It will retain the warning chimes that are lost when the factory radio is removed. The GMRC-03 will also provide a 12 volt switched accessory wire for proper radio operation. *Note: The GMRC-03 can be used in Cadillac’s that come with a factory amplifier; however the factory amplifier must be bypassed and the speaker wires on the GMRC-03 must not be used. Running new wires to the speakers is recommended. If the Cadillac also has Onstar, that feature will be lost.

1992-95 Cadillac Eldorado & Seville Pro.Vit VSM Installation

STEP 1. Begin by removing the small black trim ring that surrounds the radio. Insert the hook tool behind the upper right corner of the trim ring and pull toward you to loosen the ring. Once the ring is loose, work the remaining three (3) corners of the trim ring loose. Set the trim ring aside. Turn the ignition to the “ON” position and shift the transmission into low gear. Just above the ashtray door, grasp the top section of the bezel that surrounds the transmission shifter and pull toward you to release two (2) clips. Insert the hook tool behind the right rear corner of the bezel just behind the shifter. Pull upward to release one (1) clip. Perform the same action in the left rear corner releasing one (1) more clip. Grasp the rear of the bezel and continue working loose two (2) clips on the left and right sides of the shifter. Work the bezel up and over the shifter knob and disconnect all wiring. Set the bezel aside.