Test each corner for fit to ensure that the corners are correct.
Option #1: If covering each piece separately:
A) Start by applying the foam edge tape to corner pieces by running it along the entire edge of the panel stopping at both the top and the bottom where the edge of the panel meets the step where the corner pieces are fitted and fixed into the center section. Apply foam tape along the edge of entire center section, keeping the same idea to stop short of the sides that contain the mounted retainer strips that corner pieces will be mounted on.
Showing posts with label flat surface. Show all posts
Showing posts with label flat surface. Show all posts
Friday, June 4, 2010
55-59 Chevy Truck Kobi Rear Cab Cover Installation
5:19 AM by onesecond
·
0
comments
Labels: backside, Chevrolet, chevy truck, corner pieces, correct option, edge tape, flat surface, foam tape, glue dries, holes, installation test, option 1, PDF Download, pipe glue, retainer, top edge, weights
Labels: backside, Chevrolet, chevy truck, corner pieces, correct option, edge tape, flat surface, foam tape, glue dries, holes, installation test, option 1, PDF Download, pipe glue, retainer, top edge, weights
Tuesday, June 1, 2010
1996-2000 Honda Civic EX, GX, LX Sedan Signal Mirror Installation Instructions
2:18 AM by onesecond
·
0
comments
Labels: bolts, control panel, drive pin, flat surface, footrest, holes, Honda, honda civic, honda civic ex, mirror installation, molding, nuts, plastic grip, screw, screwdriver, screws, signal mirror, speaker wire, sturdy gloves, wire harness
Labels: bolts, control panel, drive pin, flat surface, footrest, holes, Honda, honda civic, honda civic ex, mirror installation, molding, nuts, plastic grip, screw, screwdriver, screws, signal mirror, speaker wire, sturdy gloves, wire harness
Door panel removal
1. Open door and lower window.
2. Remove screw from center of armrest and remove armrest from door.
3. Disconnect wire from behind window control panel.
4. Remove screw from behind door handle and remove door handle cover.
5. Disconnect wire from behind door handle cover.
6. Remove speaker cover.
1. Open door and lower window.
2. Remove screw from center of armrest and remove armrest from door.
3. Disconnect wire from behind window control panel.
4. Remove screw from behind door handle and remove door handle cover.
5. Disconnect wire from behind door handle cover.
6. Remove speaker cover.
Tuesday, May 25, 2010
2005-2009 Dodge Durango 2WD and 4WD Part #66-1080 Torsion Key Installation
5:02 AM by onesecond
·
0
comments
Labels: 4wd, bolt, Dodge, dodge durango, enough space, fender, flat surface, GM, line measurement, PDF Download, releasing the tension, step 1, stock height, threads, torsion bar, torsion bar unloading tool, wheel, wheels
Labels: 4wd, bolt, Dodge, dodge durango, enough space, fender, flat surface, GM, line measurement, PDF Download, releasing the tension, step 1, stock height, threads, torsion bar, torsion bar unloading tool, wheel, wheels
Step 1: Prior to lifting the vehicle it is recommended that you measure the stock height so that you have a base line measurement. Measure from the bottom of the wheel to the lip of the fender, as in Insert A.
Position vehicle on a flat surface and lift vehicle by the frame so that the front wheels are off the ground. Use a floor jack and jack stands or a (2) two post lift if available. Next, locate the torsion key at the rear of the torsion bar under the cab of the vehicle.
Position vehicle on a flat surface and lift vehicle by the frame so that the front wheels are off the ground. Use a floor jack and jack stands or a (2) two post lift if available. Next, locate the torsion key at the rear of the torsion bar under the cab of the vehicle.
Subscribe to:
Posts (Atom)
