Before installing the MSD Distributor, disconnect the battery cables. When disconnecting the battery cables, always remove the Negative (-) cable first and install it last.
TIMING FUNCTIONS
Before continuing with the installation, here are a few definitions you should be aware of:
Initial Timing: This is the base timing (also referred to as idle timing) of the engine before the centrifugal advance begins.
Showing posts with label weights. Show all posts
Showing posts with label weights. Show all posts
Thursday, December 30, 2010
MSD Pro-Billet Chevrolet HEI Distributor PN 8365
5:32 AM by onesecond
·
0
comments
Labels: advance mechanism, advance section, battery cables, billet, Chevrolet, curve, definitions, detonation, extreme digital, hei distributor, initial timing, mechanical advance, msd distributors, negative cable, timing functions, traction control, vacuum advance, vacuum line, vacuum source, weights
Labels: advance mechanism, advance section, battery cables, billet, Chevrolet, curve, definitions, detonation, extreme digital, hei distributor, initial timing, mechanical advance, msd distributors, negative cable, timing functions, traction control, vacuum advance, vacuum line, vacuum source, weights
Friday, June 4, 2010
55-59 Chevy Truck Kobi Rear Cab Cover Installation
5:19 AM by onesecond
·
0
comments
Labels: backside, Chevrolet, chevy truck, corner pieces, correct option, edge tape, flat surface, foam tape, glue dries, holes, installation test, option 1, PDF Download, pipe glue, retainer, top edge, weights
Labels: backside, Chevrolet, chevy truck, corner pieces, correct option, edge tape, flat surface, foam tape, glue dries, holes, installation test, option 1, PDF Download, pipe glue, retainer, top edge, weights
Test each corner for fit to ensure that the corners are correct.
Option #1: If covering each piece separately:
A) Start by applying the foam edge tape to corner pieces by running it along the entire edge of the panel stopping at both the top and the bottom where the edge of the panel meets the step where the corner pieces are fitted and fixed into the center section. Apply foam tape along the edge of entire center section, keeping the same idea to stop short of the sides that contain the mounted retainer strips that corner pieces will be mounted on.
Option #1: If covering each piece separately:
A) Start by applying the foam edge tape to corner pieces by running it along the entire edge of the panel stopping at both the top and the bottom where the edge of the panel meets the step where the corner pieces are fitted and fixed into the center section. Apply foam tape along the edge of entire center section, keeping the same idea to stop short of the sides that contain the mounted retainer strips that corner pieces will be mounted on.
Monday, May 17, 2010
MSD Pro-Billet Ready-to-Run Chrysler Distributor
3:54 AM by onesecond
·
0
comments
Labels: advance mechanism, advance section, battery cables, billet, boots, cams, Chrysler, definitions, initial timing, ions, mechanical advance, msd ignition, negative cable, PDF Download, plug style, spark plug, timing functions, vacuum source, weights
Labels: advance mechanism, advance section, battery cables, billet, boots, cams, Chrysler, definitions, initial timing, ions, mechanical advance, msd ignition, negative cable, PDF Download, plug style, spark plug, timing functions, vacuum source, weights
Before installing the MSD Distributor, disconnect the battery cables. When disconnecting the battery cables, always remove the Negative (-) cable ions before attempting the installation.
Note: An MSD Ignition Control is required to use these distributors.
Note: The terminals of this Distributor require spark plug style terminals. You may need to change the terminals and boots of your wires. MSD offers two kits, PN 8849 or PN 8848 that are supplied with nine boots and terminals.
Note: An MSD Ignition Control is required to use these distributors.
Note: The terminals of this Distributor require spark plug style terminals. You may need to change the terminals and boots of your wires. MSD offers two kits, PN 8849 or PN 8848 that are supplied with nine boots and terminals.
Saturday, March 20, 2010
6-Speed Short Shift Install
12:52 AM by onesecond
·
0
comments
Labels: 10mm socket, backside, bolts, box lid, flat blade, intake tube, lock washer, lock washers, nicety, PDF Download, phillips screwdriver, pin clip, red arrow, shaft, short shift, socket 3, torx screws, weights
Labels: 10mm socket, backside, bolts, box lid, flat blade, intake tube, lock washer, lock washers, nicety, PDF Download, phillips screwdriver, pin clip, red arrow, shaft, short shift, socket 3, torx screws, weights
1. Open the package and make sure you received all the appropriate parts.
There should be:
• Cast Shifter Arm
• Five (5) small weights
• Two (2) large weights
• One (1) shifter arm pin c/w lock washer
• Six (6) bolts: (2) short, (2) medium and (2) long, lock washers(2)
2. Start by getting all the appropriate tools that you will need:
• Flat-blade screwdriver
• Phillips screwdriver
• 10mm wrench and socket
• 13mm socket
• 14mm wrench/socket
There should be:
• Cast Shifter Arm
• Five (5) small weights
• Two (2) large weights
• One (1) shifter arm pin c/w lock washer
• Six (6) bolts: (2) short, (2) medium and (2) long, lock washers(2)
2. Start by getting all the appropriate tools that you will need:
• Flat-blade screwdriver
• Phillips screwdriver
• 10mm wrench and socket
• 13mm socket
• 14mm wrench/socket
Subscribe to:
Posts (Atom)
