G35 Coupe Aluminum Pedal Install

I purchased the Infiniti aluminum pedal set from Grubbs Infiniti in Dallas over the phone from Danny our FX45 salesmen. I believe Danny said these pedals are the ones used in the FX45. After examining them, I think he's probably right because the dead pedal is narrower and sits up higher than either the standard G35 plastic dead pedal or the Nissan 350Z dead pedal. The brake and gas pedals look the same.
Parts
All of the parts in their respective plastic bags with part numbers. These are for the 5AT. For the 6MT the clutch and brake pedals are different. Total price ~$80 shipped.

Chrysler 41TE (A-604) Piston Housing Now Included in TransTec Kits

TransTec rebuild kits for the Chrysler 41TE (A-604) now contain the low/ reverse piston housing. This housing is stamped steel and is susceptible to distortion, especially around the screw holes. Therefore, the housing should always be replaced during a rebuild. In fact, ATRA recommends using a new housing in their recent technical bulletin #231.

2007 Mercedes-Benz Sprinter

An engine that is not running does not need any fuel. This truism helps the Mercedes-Benz Sprinter to save fuel and thereby reduce its environmental impact. If the vehicle is stationary with the engine idling and the transmission in neutral for more than three seconds, the engine is automatically switched off. As soon as the driver depresses the clutch pedal again, the engine re-starts. The potential for saving fuel is considerable: in some cases, depending on application and traffic density, drivers managed to cut their fuel consumption by as much as 20%. On average, the amount saved will probably be somewhere between five and eight percent. The system performs to best advantage in urban use involving frequent stops in traffic queues or at traffic lights.

1999 Protege 1.6L Rattling Noise From Engine

APPLICABLE MODEL(S)/VINS
All 1999 Protege (1.6L) with VINs lower than JM1 BJ222* X0 140057.
All 1999 - 2000 Miata with (1.8L) VINs lower than JM1 NB353* Y0 155947.
DESCRIPTION A rattling noise may be heard from the engine when depressing the clutch or when revving the engine in neutral. In extreme cases, customers may experience noise at all times. This concern can be caused by improperly machined number 4 main cap of cylinder blocks which may result in premature wear of the thrust bearing. Customers having this concern should have their vehicle repaired using the following procedure.

2004-2007 Mazda RX-8 Engine Cranks No Start Service Bulletin

Some vehicles (mazda rx-8) may experience difficulty starting (cranks no start). This may occur after driving the vehicle a
short distance without engine reaching normal operating temperature. Examples: starting a vehicle and moving
it to wash it, engine stall due to mis-application of clutch then restart. This commonly occurs at port facilities or
dealer lots where vehicles are frequently started cold, moved for short distances and then turned off. This concern may also occur due to low cranking RPM during engine starting.

New Beetle Relay and fuse arrangement

Relay arrangements on the relay panel - Dual Horn Relay (53) 1- Load Reduction Relay (213, 100, 18) 2 - open 3 - Fuel Pump (FP) Relay (409) 4 - Wiper/Washer Intermittent Relay (377), V Wiper/Washer Intermittent Relay (377), VI Fuse placements on the relay panel A- Fuse for power windows (red connector) B- open C - Fuse for heated power seats (black connector)

1999 Mercedes Benz Truck ML 430 Air Injection Pump Operation

M33 AIR pump Engine 104, 111, 112, 113, 119, 137,166: When actuating, the voltage supply of the engine is performed via the air injection relay. Engine 104, 120: When actuating, the electromagnetic clutch air pump is actuated by force. Work instructions NOTE: Trim panel of cylinder head cover or air cleaner take off. Bolt (5) unscrew Refer to Air Pump NOTE: Pay attention to ground cable. 5/1 Air hose detach. M33

1995 Mercedes Benz E 320 Sedan (124 chassis) Cruise Control Operation

Cruise control operation. The cruise control system is ready for operation when the ignition is switched on. However, for actual operation, the vehicle speed should be above approx. 40 km/h (approx. 30 mph). As soon as the vehicle is running at the desired speed, touching switch for a short moment in direction of “Accel – Set” or “Decel – Set” will keep this speed constant until the driver engages a different speed or the system is switched off.

Chrysler 727 and 904 Pro Brake Part Installation

Your Chrysler 727 / 904 Pro Brake valvebody is designed to have a reverse lockout safety feature. To engage reverse, the shifter must be placed in reverse and the Trans brake switch must be depressed simultaneously. Install a good bolt-in sprag! If necessary, refer to a transmission manual for detailed instructions on disassembly and reassembly. The transmission should be completely disassembled, and thoroughly cleaned.