Brake System Repair Kit

Brake Caliper Wind Back Tool Set & Brake Bleeder Tube.
1. Brake Caliper Wind Back Tool:
Instruction:
Step 1: Choose a suitable brake caliper adapter, and then put it on the front side of right / left helix bolt.
Step 2: Roll the lever clockwise, move and push the adapter into the fillister of the brake caliper.
Step 3: When the work is done, and then simply roll the lever anticlockwise to remove the helix bolt.
1.2. Application: 1-1: RIGHT HAND HELIX BOLT 1-2: LEFT HAND HELIX BOLT
2: Citroen/XM, Xantia. (F/R)
3: Audi (F). FIAT/Alfa Romeo (F). Ford/Fiesta (F). ISUZU(F). HONDA/Concesto(F). Jaguar/XJ6,XJ40(F/R).BMW/318is,320i,325TD,518i,525i & 1x,740i,850ci,M5.(F). Mercedes Benz/190, 200, 300, 420, 560 series (F). Mitsubishi/Colt (F). NISSAN/Mlera, Stanza, Sunny(F).Rover/Austin, Metro,200 & 400 serles, Maestra, Montego(F).TOYOTA/Camry(F). Volvo (F). VW/ Passat, Golf GTI (F).
4: FORD Australia/NZ Telstar, Laser(R). MAZDA(R). SAAB 9000 R). FIAT/Alfa Romeo 1642.0(R).HONDA/Prelude, CRS 16i, GM/Saturn(R).GM/Grand Prix,Lumina.
5: 3/8” dr. Adapter used with extention bar and ratchet when need to apply more strength to the piston.
6: NISSAN, PRIMERA, VW/Golf IV.
7: Audi/80,90,V8+100, Coupe E(R). Rover/800 ABS. SUBARU L+Z(R). FORD/Sierra ABS, Granada, Scorpio ABS 85(R). NISSAN/Bluebird 1.8 Turbo, Silvia Turbo, Primera 2.0i LS/GS/GSX(R). PEUGEOT/405 1.9Gi,Gri, Sri, Gtxi, MI 16,605 2.0 Sri(R). TOYOTA/Celica, Corolla GT,MR2(R).VW/Golf Gti, Jeta Synchro, Jetta Gti 16v, Passat CL, GL ,GT and GT 16v, Corrado 16V scirroca GTX 16V(R).
8: GM most 1-7/8” diameter pistons.
9: GM most 2-1/8” diameter pistons. (CADI Seville/Eldorad 80-85).
0: GM most 2-1/2” diameter pistons. (Seville/Eldored 79).
A: Renault/R21, Laguna (Rear Disk).
M: Ford Motors Mini Cooper.
Installment and operation:
Step 1: Release the old brake oil as much as possible from the brake master cylinder.
Step 2: Fill the new brake oil into brake master cylinder.
Step 3: Before installment, please confirm the size of the small black rubber pipe which in copper adapter to fit the nozzle. As ” Fig. B ” shows that you could screw and separate No.2 copper adapter and install suitable black rubber pipe.
Step 4: Install the single-way brake bleeder tube on the nozzle, connect No.2 copper adapter with No.1 nozzle.
Step 5: Loosen the nozzle with hex wrench and release the pressure.
Step 6: Press the pedal for few times and release remained old oil, repeat this step until the single-way brake bleeder tube shows light and clear oil. The work is done.

Source