Chrysler 41TE (A-604) Piston Housing Now Included in TransTec Kits

TransTec rebuild kits for the Chrysler 41TE (A-604) now contain the low/ reverse piston housing. This housing is stamped steel and is susceptible to distortion, especially around the screw holes. Therefore, the housing should always be replaced during a rebuild. In fact, ATRA recommends using a new housing in their recent technical bulletin #231.

2005-2006 Chrysler 300C Vehicle Wiring

WIRING INFORMATION: 2005 Chrysler 300C WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE Must go to battery for 12V constant. STARTER WIRE PINK/DK.GREEN Ignition Harness SECOND STARTER WIRE PURPLE/BROWN Ignition Harness The second starter wire is a negative trigger through a 180-ohm resistor. IGNITION WIRE PINK/WHITE Ignition Harness ACCESSORY WIRE PURPLE/BROWN Ignition Harness The accessory wire is the same wire as the second starter wire. The accessory wire is a negative trigger through a 610-ohm resistor. POWER DOOR LOCK AND UNLOCK PURPLE/DK.GREEN Harness In Driver’s Kick Panel Lock is a negative trigger through a 330-ohm resistor. Unlock is

2005-2008 Chrysler 300 2.7L, 3.5L, 5.7L & 6.1L Instructions Sheet

Before removing the factory alternator you must complete the wire check as noted.
Wire Check: The original alternator is externally regulated by the computer. The original plug has two wires, one will have 12.6 volts with the key turned on and the other is the regulation wire. You will have to determine what the wires are conncted to do. This process is as follows: With the vehicle in park and the parking break on, start the vehicle. Using a volt meter, test each of the alternator plug wires. The wire that has the highest voltage is the main power for the voltage regulation. Mark or remember which wire is which for item #5 below.

Chrysler Easy-Out Roller Seat Base Installation

Chrysler’s Easy-Out Roller seat base attachments engage recessed floor strikers (supports). Two release handles are located at the rear of the seat base. Squeezing the handles and rotating the handles downward disengages the attachments and deploys the wheels. A lock indicator button pops up when the seat is unlocked.
Squeezing the handles and rotating the handles upward engages the attachments. The indicator button returns into the handle when the attachment mechanism is in the fully engaged position (seat base attachments are fully Squeeze and push down on handle to disengage seat (two handles per seat).

Chrysler 300C 5.7L Hemi Engine Dynomax Kit 19412 Installation

This dynomax kit for chrysler 300C 5.7L Hemi Engine installation steps:
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂" clamps that connect the mufflers to the x-pipe.

Chrysler, Dodge and Plymouth Transmission Mount Installation Instructions

Installation instructions:
1. Remove the bracket assembly from the vehicle.
2. Remove all of the old rubber from inside of the original shell before installing the New Energy Suspension bushings. If heat is used to remove the old rubber, you need to only heat the outer shell enough to loosen the bond of the old rubber. Do NOT burn out the bushing. Always use the proper protective/safety gear for the job and work in a well ventilated area.

Chrysler Throttle Lever Adapter Kit Catalog #1481 Installation Instructions

The #1481 Chrysler Throttle Lever Kit will allow you to connect Chrysler throttle linkages to the Edelbrock Performer Series Carburetor. Please study these instructions carefully before installing your Throttle Lever Adapter Kit.

2008 Dodge Grand Caravan / Chrysler Town Dealer Installed Factory Remote Start Components

This instructional manual will discuss the installation of the hood switch harness & XBM (Remote Start) turn-on. Other steps will include replacement procedure of the WIN, antenna installation, hood switch installation, and uploading of vehicle configuration from Dealer Connect. Refer to the vehicle Service Manual for specific installation procedures for all components except the hood switch harness, which is covered here in detail.

03-05 Chrysler PT Cruiser Turbo P/N 300-138 Installation

Remove the Factory Air Box Lid
a) Loosen the clamp on the factory intake tube at the air box lid.
b) Unclip the factory air box lid and remove from vehicle.
c) Extract the factory air filter box assembly. (Note: leave the base in place)
d) Unclip and remove the small intake tube attached to the factory air filter box.
e) Replace the factory air filter box in its original place and re-connect the hose it its original location.

MSD Pro-Billet Ready-to-Run Chrysler Distributor

Before installing the MSD Distributor, disconnect the battery cables. When disconnecting the battery cables, always remove the Negative (-) cable ions before attempting the installation.
Note: An MSD Ignition Control is required to use these distributors.
Note: The terminals of this Distributor require spark plug style terminals. You may need to change the terminals and boots of your wires. MSD offers two kits, PN 8849 or PN 8848 that are supplied with nine boots and terminals.

Chrysler-Dodge Radio Wire Harnesses Installation

If your original radio had a braided strap bolted to the rear of the radio.
TIP: Crimp a ring terminal to the new radios ground wire and insert a bolt through both connectors to connect the ring terminal of the braided ground wire to the ring terminal attached to the new radios ground wire.
If your original radio had a plastic connector containing a single wire plugged into the rear of the radio.
TIP: Crimp a male tab spade to the new radios ground wire. Slide it into the female tab spade connector that had originally snapped into the rear of the factory radio.

U-Cut-To-Fit GM & Chrysler Speedometer Cable Kit Installation Instructions

U-Cut-To-Fit Speedometer Cable Kit Installation
Step 1: Install outer housing to speedometer and route housing to transmission, making sure to keep away from exhaust pipes.
Step 2: Hold housing up to transmission to determine length and mark a cut line. Remove housing from vehicle and cut housing at the cut line.
Step 3: After cutting housing, install end of housing into GM or Chrysler trans end fitting. Figure 1 Slide housing nut up and tighten until housing is locked into fitting.
Note: Do Not over tighten nut as it will result in fitting failure.

2005+ Chrysler Vehicles Auxiliary Audio Input Installation

Installation:
The CHYX plugs into the back of the factory radio.
1. Remove factory radio. Remove factory female 10 pin Satellite cable, if available. Plug the CHYX’s 10 pin SAT plug into the radio. Plug the factory Satellite cable that was just removed into into the CHYX’s 10 pin connector.
2. Insert the CHYX’s 22 pin main power Plug (T-Harness) in between the factory radio and factory harness.
3. Connect external audio devices(s) into Aux 1 and/or Aux 2 inputs using the RCA jacks on the CHYX.

Chrysler Magnum, Charger, 300C, SRT-8 Anti-roll Bar Set Installation

1) Secure the rear wheels with blocks and jack the front up. Support the front of the vehicle with jack stands on the frame. Observe the stock sway bar orientation and position for reference.
Note: If you are using a 4 post lift or alignment rack, you do not have to jack the front up.
2) Remove the heat shields that cover the subframe mounts using a 10mm wrench or socket.
3) Remove the subframe mounts by unbolting 2 bolts per mount using a 15mm socket. The Sway bar should be hanging by it’s endlinks at this point. Retain all hardware and brackets for reinstallation.

Small Block Chrysler 727 to GM DRCE Engine Adaptor Installation

This Adapter Plate is designed to cover Flexplate only. To protect the Bellhousing area we suggest using the CSR Shield #834. Tech Officials will require a transmission shield. Care must be taken to ensure that this bolt does not Interfere with the Starter Bolt (binding can occur). Starter mountings can vary on DRC Engines. Contact us for Starter Reduction Adaptor Blocks.

Chrysler 300C/SRT-8 Headlight Disassembly

1) Remove the high beam bulb and turn signal bulbs, this allows the inside of the lamp to heat at the same rate as the outside of the lamp.
-First, test fit the headlight in the cool oven. The lamp should be situated in the center of the oven, away from the heating element. You can use a cookie sheet to shield the light from direct heat.
-Preheat the oven to 235 degrees, once pre-heated insert the lamp and set a timer for 20 Minutes.

2006 Dodge Challenger

A new concept coupe to be shown at the Detroit auto show in January will take the name of Challenger. The long-expected two-door will take on the Ford Mustang directly with a chassis derived from Chrysler's 300C/Magnum twins, along with a 425-hp version of the HEMI V-8 in the most thrilling versions. Chrysler is expected to show the car as a concept at the show, but insiders suggest the vehicle will be in production as early as 2009 on a new version of the 300C platform. Chrysler has only offered this official sketch of the concept prior to the January auto show debut, but these spy shots were taken last week as the vehicle was prepared for its auto-show debut.

Parrot UNIKA for Chrysler Cars

Parrot UNIKA is a universal interface that allows you to control the Parrot MKi9000/MKi9100/MKi9200 directly with the OEM steering wheel commands. Parrot UNIKA can work with car protocols such as CAN, KBUS or resistive systems.

Installation of the Parrot MKi
We recommend you to install the Parrot MKi before installing the UNIKA. Make sure the installation is correctly performed by checking if the Good bye message is displayed when you turn off the ignition.
Refer to the documentation of your Parrot MKi for more information

Chrysler 727 and 904 Pro Brake Part Installation

Your Chrysler 727 / 904 Pro Brake valvebody is designed to have a reverse lockout safety feature. To engage reverse, the shifter must be placed in reverse and the Trans brake switch must be depressed simultaneously. Install a good bolt-in sprag! If necessary, refer to a transmission manual for detailed instructions on disassembly and reassembly. The transmission should be completely disassembled, and thoroughly cleaned.

Howler Concept Vehicle Radio Communication Equipment Installation

The information contained in this guide has been prepared for use by persons installing two-way radio equipment (transmitters and receivers) in vehicles. It has been prepared in accordance with current engineering principles and generally accepted practices, using the best information available at the time of publication. It is not possible to cover all of the possible installations of two-way radio equipment in this guide. Accordingly, DaimlerChrysler Corporation cannot be held responsible for incidental or consequent damages arising out of the use of the information contained herein. Installations and modifications are solely the customer’s responsibility