Installation: Read all warnings before starting installation.
1. This bracket mounts above the radiator. Remove the front fascia to gain access to the radiator (see manufacturers instructions).
Thursday, January 6, 2011
2006 Chevrolet Express SA315 Speaker Mounting Bracket
4:30 AM by onesecond
·
0
comments
Labels: 2006 chevrolet, Chevrolet, chevrolet express, mounting bracket, speaker
Labels: 2006 chevrolet, Chevrolet, chevrolet express, mounting bracket, speaker
2010-up Chevrolet Camaro Hurst Billet Comp/Plus Shifter
4:23 AM by onesecond
·
0
comments
Labels: 2010 chevrolet, Chevrolet, chevrolet camaro, hurst billet, plus shifter
Labels: 2010 chevrolet, Chevrolet, chevrolet camaro, hurst billet, plus shifter
This shifter is constructed of a solid billet steel and chrome plated upper stick, billet aluminum bearing housing, billet stain- less steel adapter and high temperature Teflon® inserts. You can expect reduced shift throw (over 40%), increased strength and better, firmer, yet smoother and more precise feel thanks to extremely tight design and manufacturing
Monday, January 3, 2011
99-04 Ford SuperDuty ¾ ton 2WD F250 Spring Part# 2814 HD
Spring kits are to be installed on vehicles with stock suspensions only. Installation images corresponding to numbered process steps on next page. Note: Application requires a front-end realignment post spring installation. Note: Application requires replacement of existing shock absorber with an extended vertical travel model.
06 Chevrolet Aveo/Wave Cruise Control Installation Instructions
3:32 AM by onesecond
·
0
comments
Labels: 10mm, 5mm, aveo, Chevrolet, chevrolet aveo, cruise control module, fuse, knee panel, lettering, metal bracket, pin connector, screws, shroud, side kick panel, steel panel, steering column, switch harness, tape measure, wire harness, yellow wires
Labels: 10mm, 5mm, aveo, Chevrolet, chevrolet aveo, cruise control module, fuse, knee panel, lettering, metal bracket, pin connector, screws, shroud, side kick panel, steel panel, steering column, switch harness, tape measure, wire harness, yellow wires
INSTALLATION
1) Remove knee panel under steering column, then remove (6) 10mm screws to release steel panel.
2) Remove lower steering column cover and driver side kick panel.
3) Connect the Red Cruise Harness Wire to Pink 12v Ignition Vehicle Wire behind fuse.
4) Connect the Black Cruise Harness Wire to Black Wire/Position 87 of 4
1) Remove knee panel under steering column, then remove (6) 10mm screws to release steel panel.
2) Remove lower steering column cover and driver side kick panel.
3) Connect the Red Cruise Harness Wire to Pink 12v Ignition Vehicle Wire behind fuse.
4) Connect the Black Cruise Harness Wire to Black Wire/Position 87 of 4
UnderPro Siren Speaker Bracket for 2006 Chevrolet Express Installation Guide
3:25 AM by onesecond
·
0
comments
Labels: 12 volts, brackets, chassis, Chevrolet, chevrolet express, drain hole, exit hole, fender, hex head bolts, holes, nuts, siren speaker, sirens, speaker bracket
Labels: 12 volts, brackets, chassis, Chevrolet, chevrolet express, drain hole, exit hole, fender, hex head bolts, holes, nuts, siren speaker, sirens, speaker bracket
This bracket mounts into existing holes in the front fender that match up to the brackets mounting holes. The bracket can be ordered for either the right or left side of the vehicle. Passenger side mounting is shown.
2001-2002 Chevrolet/GMC 4X4 HD / 3/4 Ton Track Bar Kit PN. 71200
3:22 AM by onesecond
·
0
comments
Labels: bolt, Chevrolet, chevrolet gmc, dowels, GMC, gmc 4x4, illustration, illustrations, proper alignment, rear axle, rear brake caliper, rear spring, rear tire, spacer, spring pack, torque, track bars, u bolts, urethane bushings, washers
Labels: bolt, Chevrolet, chevrolet gmc, dowels, GMC, gmc 4x4, illustration, illustrations, proper alignment, rear axle, rear brake caliper, rear spring, rear tire, spacer, spring pack, torque, track bars, u bolts, urethane bushings, washers
1. Working on one side of the vehicle at a time, raise the rear tire off the ground, place a jack stand on the flat part of the frame ahead of the rear spring and remove the wheel.
2. Support the axle with your floor jack and remove the U-bolts from the axle.
3. Carefully lower the axle away from the spring pack until there is sufficient clearance to insert the track bar adapter (Driver Side 90-1587 / Passenger Side 90-1588) between the spacer block and the axle mount pad as shown in Illustration 1.
2. Support the axle with your floor jack and remove the U-bolts from the axle.
3. Carefully lower the axle away from the spring pack until there is sufficient clearance to insert the track bar adapter (Driver Side 90-1587 / Passenger Side 90-1588) between the spacer block and the axle mount pad as shown in Illustration 1.
1953/54 Chevrolet RainGear Wiper System Installation Instructions
3:20 AM by onesecond
·
0
comments
Labels: 54 chevrolet, ashtray, Chevrolet, control cable, electrical system, electrical wiring, glove box, hex nuts, original cars, pivot shafts, radio speaker, radio support, raingear, spool assembly, stock radio, studs, support bracket, vacuum motor, wiper arms, wiper motor
Labels: 54 chevrolet, ashtray, Chevrolet, control cable, electrical system, electrical wiring, glove box, hex nuts, original cars, pivot shafts, radio speaker, radio support, raingear, spool assembly, stock radio, studs, support bracket, vacuum motor, wiper arms, wiper motor
Pacific Western Design 53/54 Chevrolet Wiper System is designed to install in cars which are modified to use a 12- volt negative ground electrical system only and is not available for 6-volt(original)cars.
Subscribe to:
Posts (Atom)
