Remove the heat exchanger from its carton and inspect for any obvious physical damage. All kit components are thoroughly inspected and carefully packaged prior to shipment from the factory. If any shipping damage is evident, contact your supplier and request that they process a claim with the shipper involved. Be sure to review the parts list on to verify that you have all necessary system components to proceed. If any components in the parts list are missing, contact Turbonetics’ customer service staff.
Thursday, December 30, 2010
MSD Pro-Billet Chevrolet HEI Distributor PN 8365
5:32 AM by onesecond
·
0
comments
Labels: advance mechanism, advance section, battery cables, billet, Chevrolet, curve, definitions, detonation, extreme digital, hei distributor, initial timing, mechanical advance, msd distributors, negative cable, timing functions, traction control, vacuum advance, vacuum line, vacuum source, weights
Labels: advance mechanism, advance section, battery cables, billet, Chevrolet, curve, definitions, detonation, extreme digital, hei distributor, initial timing, mechanical advance, msd distributors, negative cable, timing functions, traction control, vacuum advance, vacuum line, vacuum source, weights
Before installing the MSD Distributor, disconnect the battery cables. When disconnecting the battery cables, always remove the Negative (-) cable first and install it last.
TIMING FUNCTIONS
Before continuing with the installation, here are a few definitions you should be aware of:
Initial Timing: This is the base timing (also referred to as idle timing) of the engine before the centrifugal advance begins.
TIMING FUNCTIONS
Before continuing with the installation, here are a few definitions you should be aware of:
Initial Timing: This is the base timing (also referred to as idle timing) of the engine before the centrifugal advance begins.
Chevrolet/GMC Chevrolet/GMC Posi-Lok Installation Instructions
Pre-Installation Information Special Tools
T-30 and T-40 torx male drivers (required only on 1994 or newer vehicles); Unibit #3 for 9/16” hole; 7mm and 10mm socket drivers; 3/32 Allen wrench
1. This is a universal kit designed to fit all T-10/15’s. You will have some parts left over. While installing, you will need to study the pictures and use good judgement.
T-30 and T-40 torx male drivers (required only on 1994 or newer vehicles); Unibit #3 for 9/16” hole; 7mm and 10mm socket drivers; 3/32 Allen wrench
1. This is a universal kit designed to fit all T-10/15’s. You will have some parts left over. While installing, you will need to study the pictures and use good judgement.
1998-2002 Chevrolet Cavalier Cold Air Intake System Part Number 21-447
The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot under hood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power.
1941-48 Chevrolet Style Tail Lights Installation Instructions
2:56 AM by onesecond
·
0
comments
Labels: 1941, array, cars, Chevrolet, gasket, holes, light circuit, lock washers, nuts, permanent damage, signal circuit, stainless steel, studs, suitable location, tail lights, turn signal, turn signals
Labels: 1941, array, cars, Chevrolet, gasket, holes, light circuit, lock washers, nuts, permanent damage, signal circuit, stainless steel, studs, suitable location, tail lights, turn signal, turn signals
1. Disconnect Battery. Do not skip this step. Also, do not try to “test” the LED array by connecting the leads directly to your battery. Permanent damage will occur to the LED array if you fail to heed these steps.
2. Choose a suitable location to mount the taillight.
3. Using the supplied template, mark the centers of the three holes required for installation.
4. Drill two (2) 1/4” holes for the mounting studs and one (1) 3/8” hole for the wiring.
2. Choose a suitable location to mount the taillight.
3. Using the supplied template, mark the centers of the three holes required for installation.
4. Drill two (2) 1/4” holes for the mounting studs and one (1) 3/8” hole for the wiring.
1957 Chevrolet Louver & Switch Package Automotive Air Conditioner
Automotive air conditioning installation requires a basic knowledge of refrigeration systems and services of a qualified mechanic. These instructions explain the steps necessary or the installation of this unit but do not detail standard workshop procedures or safely practices.
Chevrolet Silverado Rear Vision System Nav Display Installation Instructions
1:35 AM by onesecond
·
0
comments
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Labels: bezel, bolts, center punch, Chevrolet, chevrolet silverado, figure 1, inset, lamps, latch handle, mounting bolt, negative battery cable, preparation 1, punch mark, rear vision system, retainer, sill plate, socket 6, step 8, template sheet, work surface
Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
Subscribe to:
Posts (Atom)
